DATREND Systems vPad-TI Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 86

background image

vPad-TI OPERATING MANUAL

In addition, the

Incubator (air) Temperature

and the

Mattress Temperature

will be

displayed on a minute to minute basis. The

Average Incubator Temperature

and the

Average Relative Humidity

will not be displayed until

STC

is reached. During the time before

STC

is true, the buttons labeled

Humidity Check

and

Temperature Check

are also disabled

(grayed out). After

STC

is true, these buttons will be enabled for input.

During the test, all of the data points collected, including those for the temperatures at the other 4
locations, are saved to a Raw Data file. All five temperatures for locations Ta through Te are
displayed along the bottom of the graph for information purposes. Any event which occurs during
the test is also saved as a comment. Typical comments would be: Minute Mode, Air Temperature
Control (Mattress Horizontal) at 36 °C Started, Waiting for STC, Humidity Check Pass, etc. The
Raw Data file can be exported and used to recreate the test graphics.

Figure 73

Figure 74

Running a Test/Chapter 5

#

Page 55

«
...
65
66
67
68
69
...
»

Содержание vPad-TI























































































Отзывы:

Нет отзывов

Похожие инструкции для vPad-TI

Бренд: GE Страницы: 138

Бренд: Cadman Страницы: 66

Бренд: VeEX Страницы: 2

Бренд: JB-Lighting Страницы: 48

Бренд: Patty-O-Matic Страницы: 28

Бренд: YMC Страницы: 49

Бренд: Octane Fitness Страницы: 8

Бренд: Octane Fitness Страницы: 10

Бренд: OCENCO Страницы: 48

Бренд: Ocean Optics Страницы: 6

Бренд: Ocean Sonics Страницы: 45

Бренд: Hach Страницы: 456

Бренд: Yamaha Страницы: 4

Бренд: Wacker Neuson Страницы: 120

Бренд: Dantel Страницы: 22

Бренд: RainPoint Страницы: 40

Бренд: FARM-MAXX Страницы: 35

Бренд: GE Страницы: 37

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды