Cumberland PRO-VISION, Руководство пользователя

Страница: 38 / 55

38
PRO-VISION rev.04
PRO-VISION
End meter 1-2 — Set the maximum allowable
amount of water that can be consumed by the
birds at the end of the flock in per 15-minute
period. Set this parameter separately for each
water meter in use. It ranges from 0 to 10,000
gallons (or liters).
End Age — Select the age at which the flock
ends. When it is reached, the controller keeps
using the water spill alarm limit defined for
that day until a new flock begins. *
This pa-
rameter is common to both water meters.
13.2.4. Feeder Alarm
The controller can declare an alarm if a feeder
runs continuously for a too long period of
time. When this type of alarm occurs, the
relay associated with the problematic feeder
opens in order to stop the feeder motor.
Select: 1.
Main menu
Alarms
* Feeder Alarm
* This menu is accessible if a feeder is enabled in the
Set-up menu (see section 4.4). A password may also
be required to access it (see section 4.2.1).
Feed monitoring: No
Feed Max time Send alarm Restart
Feed 1 0:10 H:M Yes No
Feed 2 0:10 H:M Yes No
Feed 3 0:10 H:M Yes No
Feed 4 0:10 H:M Yes No
Feed monitoring — Select “Yes” to enable the
feeder monitoring function.
Max Run Time — Set the maximum run time
of each feeder separately.
Send alarm — Select
“Yes”
for an alarm to set
off when the run time of a feeder exceeds its
respective maximum time.
Restart — When a run time alarm occurs, the
controller opens the relay associated with
the feeder in order to stop the feeder motor.
After a run time error occurred, select
“Yes”
to allow the feeder motor to restart.
13.2.5. Amperage Draw Alarm
If current sensors are used, the controller can
set off an alarm if the amperage draw of an
output gets out of range.
Select: 1.
Main menu
Alarms
* Amp draw
* This menu is accessible if at least 1 relay uses a
current sensor. A password may also be required to
access it (see section 4.2.1).
A table containing all outputs that are using a
current sensor is displayed. Refer to section
4.8.1 to specify what relays are using this
type of sensor.
Amp draw alarm
Item Minimum Maximum
Heaters 1.0A 5.0A
Fan 1.0A 5.0A
Tun Fan 1.0A 5.0A
Cooling 1.0A 5.0A
Stir 1.0A 5.0A
Time clock 1.0A 5.0A
Light 1.0A 5.0A
Wtr line 1.0A 5.0A
Backup 1.0A 5.0A
Sidewall 1.0A 5.0A
Tun inlet 1.0A 5.0A
Attic 1.0A 5.0A
Eg.Cool 1.0A 5.0A
Eg.Htr 1.0A 5.0A
Eg.RH 1.0A 5.0A
To modify use -
Minimum / Maximum — Select the acceptable
amperage draw range for each output that
uses a current sensor.
0-10V Output Error 13.2.6.
The controller signals a 0-10V output error
when the output voltage is 0.5V above or
below the target voltage and sets off an alarm
if the voltage difference increases to 1.0V.
A 0-10V error is likely to occur if the load
connected to the output exceeds the output’s
rating (30 mA) or if there is electrical noise
on the output.
13.2.3. Water Spill Alarm
A water spill alarm is declared when the water
consumption exceeds the acceptable limit.
This limit ranges from 0 to 10,000 gallons
or liters per 15 minutes.
The controller can also adjust the water spill
limit of each water meter automatically as the
animals are growing. The water spill alarm
limit changes in a linear fashion between 2
user-defined steps: the first step being the
maximum water consumption allowed at
the beginning of the flock (-5 days) and the
second step being the maximum consumption
at the end of the flock.
1 day
End
Age
Age
(days)
End
meter x
Water Spill
Limits
(gal/15 min)
Water Spill
Alarm Limit
Start
meter x
Select: 1.
Main menu
Alarms
* Water
*This menu is accessible if at least 1 water meter in
enabled in the Set-up menu (see section 4.4). A
password may also be required to access it (see sec-
tion 4.2.1).
Set the following parameters. 2. *The param-
eters below are common to all programs.
Water spill alarm settings
Start meter 1
Start meter 2
End meter 1
End meter 2
End Age
5g/15m
5g/15m
25g/15m
25g/15m
5
Start meter 1-2 — Set the maximum allowable
amount of water that can be consumed by
the birds at the beginning of the flock in per
15-minute period. Set this parameter sepa-
rately for each water meter in use. It ranges
from 0 to 10,000 gallons (or liters).