Cumberland PRO-VISION, Руководство пользователя

Страница: 40 / 55

40
PRO-VISION rev.04
PRO-VISION
14.2. History Menus
The history menus provide a daily record of
the house conditions. The information con-
tained in these menus is logged at midnight
everyday.
Select: 1.
Main menu
History
By default, the controller displays the 2.
average temperature history at first. Use the
menu selector to select the desired type of
history:
Average — This menu contains the daily mini-
mum and maximum readings of the average
temperature of the past 400 days (or since
the beginning of the flock).
T° Sensors — This menu contains the daily
minimum and maximum temperature readings
of each inside & outside temperature sensors
of the past 7 days.
RH — This menu contains the daily minimum
and maximum relative humidity readings of
the past 400 days (or since the beginning of
the flock). *
This history menu is accessible if a
humidity sensor is enabled in the Set-up menu (see
section 4.4).
S.P.— This menu contains the daily minimum
and maximum static pressure readings of the
past 400 days (or since the beginning of the
flock). *
This history menu is accessible if a static
pressure sensor is enabled in the Set-up menu (see
section 4.4).
Heaters — This menu contains the daily
run time of each heating output of the past
400 days (or since the beginning of the
flock)
Feeders — This menu contains the daily run
time of each feeder of the past 400 days (or
since the beginning of the flock). *
This history
menu is accessible if a feeder is enabled in the Set-up
menu (see section 4.4).
Water— This menu contains the daily water
consumption of each water meter of the past
Animal Age & Count 14.3.
Animal Age: Some parameters of the control-
ler can automatically change over time as the
animals grow up (temperature ramps, light
programs, etc.).
Animal Count & Mortality: In order to keep
the animal count, you must first specify the
initial number of animals at the beginning of a
flock. You must then update the animal count
when mortality occurs.
Select: 1.
Main menu
* Start Flock
* A complete-access password may be required to
access this menu (see section 4.2.1).
On top of the “Start flock” menu are some
information about the current breeding (total
number of mortalities, # of remaining birds
and loss rate). These values are displayed as
a reference only and cannot be modified.
History
Average Temperature
Average
Feeders
T°
Sensor
Water
Mortal. RH
S.P.
Heaters
10
12:00:00 am
0.0
12:00:00 am
0.0
9
12:00:00 am
0.0
12:00:00 am
0.0
8
12:00:00 am
0.0
12:00:00 am
0.0
7
12:00:00 am
0.0
12:00:00 am
0.0
6
12:00:00 am
0.0
12:00:00 am
0.0
5
12:00:00 am
0.0
12:00:00 am
0.0
4
12:00:00 am
0.0
12:00:00 am
0.0
3
12:00:00 am
0.0
12:00:00 am
0.0
2
12:00:00 am
0.0
12:00:00 am
0.0
1
12:00:00 am
0.0
12:00:00 am
0.0
Age Minimum Maximum
400 days (or since the beginning of the flock).
*
This history menu is accessible if a feeder is en-
abled in the Set-up menu (see section 4.4).
Mortal —
This menu contains the daily
number of mortalities recorded in the past
400 days (or since the beginning of the
flock).
Set the following parameters: 2.
Age — The animal age ranges from -5 days to
450 days. Negative day values are used to pre-
pare the house before letting the animals in.
Birds placed — Specify the initial number
of birds.
Start Flock — Before starting a new flock,
make sure the number of birds placed is set
properly.
ALL information contained in the history
menus of the controller are reset when
a new flock starts.
New Mortal. — Post the number mortalities
as it occurs. Once it is validated, the value
automatically goes back to “0”. The posted
value is added to the
“Mortality” count and
removed from the “Remaining” count. Note
that it is always possible to enter a negative
value with the +/- key in order to readjust the
number of mortalities if a mistake is made.
Start flock
To modify use -
Mortality
Loss (%)
Stat Flock
Age
Clean Mode
Remaining
Birds placed
Age
Program
New Mortality
0
0.00
No
10000
Off
10000
10000
Program 1
0