Covidien Puritan Bennett 700 Series Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 439

Covidien Puritan Bennett 700 Series Скачать руководство пользователя страница 4

Preface

iv

10070389 Rev. A

Puritan Bennett™ 700 Series Ventilator System Service Manual

Preface

This manual is intended to provide information needed to service the Puritan Bennett™
700 Series Ventilator System. It is intended for use by certified biomedical engineering
technicians or personnel with equivalent experience and training in servicing this type of
equipment. The user should complete the Covidien training class geared specifically to the
740 or 760 Ventilator System.

While this manual covers the ventilator configurations currently supported by Covidien, it
may not be all-inclusive and may not be applicable to your ventilator. Within the USA, contact
Covidien at 1-(800)-635-5267 for questions about the applicability of the information.

Definitions

This manual uses three special indicators to convey information of a specific nature. They
include:

Warning

Indicates a condition that can endanger the patient or the ventilator operator.

Caution

Indicates a condition that can damage the equipment.

NOTE:

Indicates points of particular emphasis that make operation of the ventilator more
efficient or convenient.

Warnings, cautions, and notes

Please take the time to become familiar with the following, as they cover safety
considerations, special handling requirements, and regulations that govern the use of the
700 Series

Ventilator Systems.

Warning

To ensure proper servicing and avoid the possibility of physical injury, only qualified
personnel should attempt to service or make authorized modifications to the
ventilator.

The user of this product shall have sole responsibility for any ventilator malfunction
due to operation or maintenance performed by anyone not trained by Covidien staff.

Warning

To avoid an electrical shock hazard while servicing the ventilator, be sure to remove all
power to the ventilator by disconnecting the power source and turning off all
ventilator power switches.

«
...
2
3
4
5
6
...
»

Содержание Puritan Bennett 700 Series
























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды