manualshive.com logo in svg

Covidien Puritan Bennett 700 Series, Руководство по обслуживанию

Поделиться
Скачать
Covidien Puritan Bennett 700 Series Скачать руководство пользователя страница 312

Service and repair

8-54

10070389 Rev. A

Puritan Bennett™ 700 Series Ventilator System Service Manual

8.10.4  Cylinder and exhalation pressure transducer autozero solenoids

(See Figure 8-40). Remove the cylinder or exhalation pressure transducer autozero solenoid as 
follows. Install by reversing removal procedure.

1.

Open and prop lid (Section 8.5.1).

2.

Disconnect tubes from applicable solenoid.

Caution

To prevent equipment damage, never disconnect any solenoids while power is applied.

3.

Disconnect solenoid harness from ventilator head harness at cable management bar.

4.

Using 7/64-in. hex driver, remove two 6-32 x 5/16 POZIDRIV™* screws and split-ring 
washers that attach solenoid to cable management bar. Remove solenoid.

NOTE:

When installing the autozero solenoids, orient them with ports pointing upward.

8.10.5  Cable management bar

(See Figure 8-40). Remove the cable management bar as follows. Install by reversing removal 
procedure.

1.

Disconnect harnesses and tubes as necessary to remove bar.

2.

Using 7-mm nutdriver, remove M4 nut and split-ring washer from bottom of bar.

3.

Using 7/64-in. hex driver, remove two 6/32 x 5/16 screws and split-ring washers that retain 
cylinder pressure transducer autozero solenoid (Section 8.10.4). It is not necessary to 
disconnect tubing or harness.

4.

Using 3-mm hex driver, remove M4 x 8 screw and split-ring washer from top of bar. 
Remove bar.

5.

Complete removal of harnesses and other solenoid.

Содержание Puritan Bennett 700 Series
























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды