Covidien Puritan Bennett 700 Series Скачать руководство пользователя страница 164 | Manualshive

Страница: 164 / 439

background image

Service and utility functions

4-4

10070389 Rev. A

Puritan Bennett™ 700 Series Ventilator System Service Manual

4.1.4 About the test and alert logs and EST test results

The results of ventilator self-tests are stored in NVRAM, as follows:

• Two logs store diagnostic codes corresponding to unexpected conditions detected by the

ventilator. Conditions detected during POST, SST, EST, and calibrations (but not the pass/
fail status of EST tests) are stored in the

test log

. Technical alerts and other conditions

detected during the ventilator’s ongoing checks are stored in the

alert log

. Each log holds

up to ten

codes, corresponding to the ten most recently detected conditions. If the same

condition is detected more than once in succession, that code is logged only once, but the
number of occurrences is incremented and the time stamp is updated.

• EST test results are stored in NVRAM separately from the test logs. The pass/fail status of

the most recent execution of each EST test is stored.

NOTE:

The EST test results stored in NVRAM are always the results from running a full EST. EST
tests run individually for diagnostic purposes (

Run tests

under

Diagnostics/Calib

) are

not retained in NVRAM.

4.2 Service functions

4.2.1 Sensor data

This function lets you view parameters monitored by the ventilator, such as pressures,
temperatures, voltages, battery current, PEEP pump current, delivered volumes, flows (BTPS),
and oxygen percentage, among others. Sensor data can be viewed at any time while the

Service

menu

is active, including while the unit is ventilating; it is the only service function

that can be used during ventilation.

To access the

Sensor data

functions from the

A. Service menu

prompt, turn the knob until

Sensor data

is displayed, then press ACCEPT. Now turn the knob to display the desired

parameter group. The parameter groups are:

• Pressure sensors

• Temperature sensors

• Battery/BBU sensors

• UI/HW sensors

• Pressure sol sensors

• Other data

«
...
162
163
164
165
166
...
»

Содержание Puritan Bennett 700 Series
























































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Puritan Bennett 700 Series

Бренд: Raymarine Страницы: 55

Бренд: Halyard Страницы: 4

Underwater Light Show & Fountain

Бренд: GAME Страницы: 2

Бренд: Canta Страницы: 2

Бренд: CAIRE Страницы: 2

Бренд: R.M. Young Страницы: 10

Бренд: XM Fitness Страницы: 10

Бренд: Magma Страницы: 16

Бренд: Nederman Страницы: 89

Бренд: Nederman Страницы: 71

Бренд: Nederman Страницы: 131

Бренд: X-Cite Страницы: 2

Бренд: L-Acoustics Страницы: 5

Бренд: Yamaha Страницы: 16

McDonnell & Miller PSE-800-M

Бренд: Xylem Страницы: 20

Quadro A Legs 3P 120 Degree Workstation with...

Бренд: Jason.L Страницы: 10

IQ Express RF6118

Бренд: Mainpine Страницы: 2

Бренд: Petromax Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды