Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 201 / 288

Edge Maxx

3024-024e

C-5

Speed Control

The unit can operate in either manual or

automatic speed mode.

In manual mode, the machine runs at the speed

shown on the CHI Panel display. In auto mode,

the machine’s speed is automatically controlled

by the Chicago

ironer or Chicago encoder

behind it.

To switch between manual and automatic

modes refer to the

Adjustments

section,

PGM

SELECTION

subsection. Set PWM to 0 for

AUTO and set PWM to 1 for manual.

AUTO Mode (PWM=0)

02 KING SHEET COTTON
*AUTO XXX FPM CNT XXXXX

Enables pre-programmed settings to

automatically follow the speed encoder signal

from the ironer to operate.

MANUAL Mode (PWM=1)

02 KING SHEET COTTON
SPEED XXX FPM CNT XXXXX

When running in manual mode, press the

SPEED





buttons at the bottom of the CHI

panel to adjust the speed setting.

NOTE: Manual mode speed

adjustments should be temporary.

To permanently set the speed for

a speciﬁc program, refer to the

Programming section.

As a general rule, start with the spreader/feeder

speed set slightly slower than the ironer speed,

up to ﬁve feet per minute.

If the feeder is set too fast, the ﬂatwork will

bunch as it feeds into the ironer. If the speed is

set too slow, the ﬂatwork will be excessively

stretched.

TOC

INDEX

C-TOC

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды