Chicago Dryer Edge MAXX Скачать руководство пользователя страница 49

Страница: 49 / 288

Edge MAXX

Operating Guidelines

3-9

Figure 3-10: Two mass sensors are located under

the lower inlet belt.

Perform a safety check:

Press a red safety STOP button. All

moving parts should stop and an error

message should display in the CHI

Panel.
Reset the red safety STOP button by

twisting it clockwise.
Restart the unit.
Test each of the 5 remaining red safety

STOP buttons in the same manner.
To test the Interconnected Stop Cir-

cuit, start another machine in the line

and press a red safety STOP button on

that machine. Make sure the spreader/

feeder shuts down, an error message

displays in the CHI Panel and the red

SYSTEM E-STOP lamp glows.
Reset the stopped unit so that the green

SYSTEM READY lamp glows.
Restart the unit.
Test the crossbeam sensor by momen-

tarily blocking the beam. All moving

parts should stop and an error message

should display in the CHI Panel.
Restart the unit
At one station, test the two mass sen-

sors one at a time. Press down on the

lower inlet belt just above a mass sen-

sor (Figure 3-10, A).
The upper arm should raise, all moving

parts should stop and an error message

should display in the CHI Panel.
Restart the unit and repeat the test with

the second mass sensor (B).
Repeat the mass sensor tests at the

other station.

Restart the unit. After the CHI Panel com-

pletes its diagnostics, for about 3 seconds

the CHI Panel displays:

EDGE MAXX

TYPE XX XX PROGRAMS

•

•
•

•

•
•

•

The screen then displays:

02 KING SHEET COTTON
*AUTO XXX FPM CNT XXXXX

02 KING SHEET COTTON
SPEED XXX FPM CNT XXXXX

In automatic operation, the speed of the

feeder is determined by the ironer.

In other applications, manually set the

speed with the



and



buttons so that

it is 0 to 5 FPM (0 - 1.5 m/min) less

than the speed of the ironer.

The spreader/feeder is now ready for

operation.

Note that if no STATION button is selected,

the display will show:

FEEDER OFF

In this case, the machine will be running

in a standby state until a STATION button is

pushed.

•

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Chicago Dryer Edge MAXX, Инструкция по эксплуатации, Страница: 49 / 288

Результаты поиска

Содержание Edge MAXX

Отзывы: