Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 118 / 288

Troubleshooting

Edge MAXX

6-16

WARNING

Only trained personnel with experience

in electrical or mechanical repair should

troubleshoot and repair the unit.

Troubleshooting

WARNING

Read the

REPAIR

chapter and make

sure that the power is disconnected

before doing any repairs.

ISSUE

POSSIBLE CAUSE

SOLUTION

Transfer Assembly does not

Travel Forward

Message Reads:

TRANSFER CYLINDER

JAMMED/

SHUTDOWN BEFORE CLEAR-

ING

1. Proximity sensor (PX28,

left or PX31 right) detect-

ed a jam or has otherwise

been activated.

Clear the jam. Refer to the

OPERAT-

ING GUIDELINES

chapter,

Daily

Operating Procedures

section,

Han-

dling Jams and Misfeeds Safely

procedure.

•

Transfer Assembly does not

Travel Forward

No message

1. When moved by hand

without air pressure,

rodless air cylinder does

not move freely along the

length of the cylinder.

Air cylinder may need adjustment.

Refer to the

REPAIR

chapter,

Com-

pressed Air System

section,

Transfer

Rodless Air Cylinder Maintenance

procedure.

•

2. Air valve malfunction.

Check. For more information within

this chapter, refer to

Compressed Air

System

section. Repair/replace as

necessary.

•

3. Fuse on output board may

be bad.

Check. Replace as necessary.

•

Corner Dropped During Trans-

fer

(continued on next page)

1. Clamp bearing and cyl-

inder rod end pivots are

binding.

Check the cylinder stroke is properly

tensioned and adjusted. With no air

pressure on the unit, they should move

freely.

•

2. Clutch rollers need clean-

ing.

Lint or threads can fool the upper cor-

ner sensors. Clean the clutch rollers as

necessary.

•

3. Sensor problems.

Check. For more information within

this chapter, refer to

Sensor Function

section.

•

4. Clutch rollers are not par-

allel and/or not touching.

Align as necessary. Refer to the

REPAIR

chapter,

Inlet Section

sec-

tion,

Pneumatic Clutch/Brake Roller

Alignment

procedure.

•

5. Check that the transfer

clamp rollers are paral-

lel to, and seat ﬁrmly and

squarely against, the

clutch rollers.

Align as necessary. Refer to the

REPAIR

chapter,

Transfer Section

section,

Transfer Clamp Roller Align-

ment

procedure. (Does not apply to

blanket models).

•

6.6 Transfer Section

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды