Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 123 / 288

Edge MAXX

Troubleshooting

6-21

WARNING

Only trained personnel with experience

in electrical or mechanical repair should

troubleshoot and repair the unit.

Troubleshooting

WARNING

Read the

REPAIR

chapter and make

sure that the power is disconnected

before doing any repairs.

ISSUE

POSSIBLE CAUSE

SOLUTION

Flatwork Pulls Out of Clamps

When Spreading

1. Spreader clamps out of

adjustment.

Adjust so the clamps close evenly

across the jaw surface. Refer to the

REPAIR

chapter,

Spread Section

section,

Spreader Clamp Mechanical

Adjustment

procedure.

•

2. Counter air pressure is set

too high.

Adjust. Refer to the

PREVENTIVE

MAINTENANCE

chapter,

Weekly PM

section,

Check Air Pressure Settings

procedure.

•

3. Spread clamps remaining

partially open.

Check/Adjust. Refer to the

REPAIR

chapter,

Spread Section

section,

Spreader Clamp Mechanical Adjust-

ment

procedure.

•

4. An incorrect inverter

setting may be causing

excessive torque.

Adjust. Contact the factory Service

Department for assistance.

•

Upper Spreader Clamps Re-

turn to the Center too Fast

1. The SPREAD slow buffer

needs to be adjusted.

Increase the SPREAD SLOW buffer

adjustment. Refer to the

CHI PANEL

OPERATION

bulletin,

Adjustment

section,

Spread Section Adjustments

procedure.

•

2. Servomotor or associated

component malfunction.

Check. Consult factory if necessary.

•

Lower Spreader Belts Stop.

Message Reads:

JAM / SENSOR AT LEFT WALL

JAM / SENSOR AT RIGHT

WALL

JAM / SENSOR AT INLET

CONV

1. Flatwork is jammed.

Clear the jam. Refer to the

OPERAT-

ING GUIDELINES

chapter,

Daily

Operating Procedures

section,

Han-

dling Jams and Misfeeds Safely

procedure.

•

2. Wall sensors may be dirty,

misaligned, or defective.

Clean/adjust/replace as necessary. For

more information within this chapter,

refer to

Sensor Function

section.

•

Lower Spreader Belts Reverse

Direction

1. Wall sensors may be dirty,

misaligned, or defective.

Clean/adjust/replace as necessary. For

more information within this chapter,

refer to

Sensor Function

section.

•

2. Debris on the belts.

Clean the belts.

•

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды