Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 128 / 288

Troubleshooting

Edge MAXX

6-26

WARNING

Only trained personnel with experience

in electrical or mechanical repair should

troubleshoot and repair the unit.

Troubleshooting

WARNING

Read the

REPAIR

chapter and make

sure that the power is disconnected

before doing any repairs.

ISSUE

POSSIBLE CAUSE

SOLUTION

Sensor Function Issue

Message Reads:

SENSOR FAILED/MIS-

ALIGNED/ INLET CONVEYOR
SENSOR FAILED/MIS-

ALIGNED/ LEFT CORNER
SENSOR FAILED/MIS-

ALIGNED/ MATERIAL TAIL
SENSOR FAILED/MIS-

ALIGNED/ MATERIAL TAUT
SENSOR FAILED/MIS-

ALIGNED/ RIGHT CORNER
SENSOR FAILED/MIS-

ALIGNED/ TRANSFER POSI-

TION
SENSOR FAILED/MIS-

ALIGNED/ UPPER SPREADER

HOME

1. Photosensor/reﬂector is

dirty.

Clean. Refer to the

PREVENTIVE

MAINTENANCE

chapter,

Weekly PM

section,

Clean the Photosensors and

Reﬂectors

procedure.

•

2. Incorrect alignment or

adjustment.

Check/adjust. Refer to the

REPAIR

chapter,

Sensors

section and the

appropriate procedure or photosensor

physical alignment procedure.

•

3. There is an open circuit

between the sensor and

the input card.

Check connections between the sen-

sor and input card. - Main control

circuit board is defective. Replace.

- Sensor is defective. Replace.

•

4. Sensor is activated and

the control board does not

respond.

Main control circuit board is defective

and needs to be replaced.

•

5. Damaged sensor cable.

Replace the sensor. For more infor-

mation, refer to the

REPAIR

chapter,

Photosensors

section,

Photosensor

Replacement

procedure.

•

6. Component is bad or fail-

ing.

Check wiring and connections. Tight-

en/repair as necessary.

Check component. Replace as neces-

sary. Refer to the

REPAIR

chapter,

Sensors

section and the appropriate

procedure.

•

Proximity Sensor Not Working

1. Encoder is not properly

positioned.

Adjust. Refer to the

REPAIR

chapter,

Sensors

section and the appropriate

procedure.

•

2. Encoder is failing or bad.

Check component. Replace as neces-

sary.

Check wiring and connections. Tight-

en/repair as necessary.

•

3. Mechanical or compressed

air device failure.

Check the mechanical system or com-

pressed air device associated with the

sensor. Repair/replace as necessary.

•

6.10 Sensor Function

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды