Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 121 / 288

Edge MAXX

Troubleshooting

6-19

WARNING

Only trained personnel with experience

in electrical or mechanical repair should

troubleshoot and repair the unit.

Troubleshooting

WARNING

Read the

REPAIR

chapter and make

sure that the power is disconnected

before doing any repairs.

6.7 Spread Section

ISSUE

POSSIBLE CAUSE

SOLUTION

The force required to move the upper spreader clamps along the linear rods is normally 2-5 pounds. If

there is extra tension on the belt, the movement may be erratic or slow. If the belt is too lose it may skip

on the pulley.

Flatwork Not Properly Spread

Message Reads:

UPPER SPREADER STALLED

1. Excessive tension in the

upper spreader belt.

Refer to the

REPAIR

chapter,

Spread

Section

section,

Upper Spreader Belt

Tension Adjustment

procedure.

•

2. Excessive friction in the

rail-carriage assembly.

Lubricate the rail. Refer to the

PRE-

VENTIVE MAINTENANCE

chapter,

Weekly PM

section,

Lubricate Upper

Spreader Rail

procedure.

•

3. Servomotor or associated

component malfunction.

Check. Consult factory if necessary.

•

4. Taut sensors PE50 A/B

malfunction.

Check. Adjust/replace as necessary.

Refer to the

REPAIR

chapter,

Sensors

section,

Photosensor Replacement

procedure.

•

5. Defective run relay (CR4)

or fuse.

Test and/or replace.

•

6. Spreader timing out of

adjustment.

Refer to the

CHI PANEL OPERATION

bulletin, spreader related

Adjustment

and

Testing

sections.

•

Upper Spreader Clamps Bang

or Drag at the Center of the

Unit

1. Clamps are bouncing

when they are ﬁnished

spreading.

Increase the SPREAD SLOW buffer

adjustment. Refer to the

CHI PANEL

OPERATION

bulletin,

Adjustment

section,

Spread Section Adjustments

procedure.

•

Upper Spreader is not Reach-

ing the Center Home Position

1. Rubber stops at center of

machine out of position.

Check. Adjust as necessary.

•

2. Debris on the spread

clamp rail.

Check/clean as necessary.

•

3. Servomotor or servomotor

controller malfunction.

Check connection cables. Consult fac-

tory if necessary.

•

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды