Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 47 / 288

Edge MAXX

Operating Guidelines

3-7

CHI Panel Controls and Indicators

The CHI panel is the heart of the operation

of the Edge spreader/feeder, making it easy to

operate as well as to program and adjust the

feeding system. The CHI feed system control

panel (Figure 3-9) is located on the right front

endframe and features these controls:

The

ADJUST

button (A) is used for adjusting

various settings in order to fine tune the

performance of the feeder.

The

programming button (B) is used to

change the preset program settings for the various

types of pieces processed by the feeder.

The

TEST

button (C) is used during

troubleshooting. The feed system must be off in

order to access the test functions.

The CHI panel Display (D) varies depending

upon which mode is currently selected. It shows

the various fold system settings, diagnostic

messages, etc.

The

CURSOR

button (E) moves the cursor

to various positions in the CHI panel Display in

order to change settings.

The “

” and “

” buttons (F and G) are used

to increase and decrease the various fold system

settings. The “

” button is also used to reset the

item counter.

The

ENTER

button (H) conﬁrms a selection

from a menu, or to store new information.

The

STATION

buttons allow for automatic

operation using preset or user programmed

values. The appropriate lamp lights to show the

currently selected station. Also, turns feed/spread

functions on or off.

The

CHI SELECT

button enables the

CORNER GRAB DELAY for ﬁne-tuning corner

size.

The

SPEED

buttons control the speed of the

unit in manual mode. Pressing



decreases the

speed and



increases the speed. The speed is

shown in the panel display.

The

BYPASS ON/OFF

button is used to

differentiate between ﬂat sheets and ﬁtted sheets.

When BYPASS is ON, the unit automatically

opens the lower spreader belts to accommodate

ﬁtted sheets or odd items. Increasing the spreader

gap will reduce the pull on multi-layer or thicker

ﬂatwork.

Figure 3-9: The Chicago High Intelligence (CHI)

control panel.

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды