Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 125 / 288

Edge MAXX

Troubleshooting

6-23

WARNING

Only trained personnel with experience

in electrical or mechanical repair should

troubleshoot and repair the unit.

Troubleshooting

WARNING

Read the

REPAIR

chapter and make

sure that the power is disconnected

before doing any repairs.

ISSUE

POSSIBLE CAUSE

SOLUTION

Laydown of Flatwork is Erratic

1. Mechanical problem with

spread clamp or its air

cylinder.

Check/adjust. Refer to the

REPAIR

chapter,

Spread Section

section,

Spreader Clamp Mechanical Adjust-

ment

procedure.

•

2. Air bars out of alignment.

Adjust. Refer to the

REPAIR

chapter,

Compressed Air System

section,

Air

Bar Alignment

procedure.

•

3. Adjust length of the air

bars blast.

Adjust. Refer to the

CHI PANEL OP-

ERATION

bulletin,

Adjustment

sec-

tion,

CHI Adjustments

procedure.

•

4. CORNER STOP DELAY

settings need adjustment.

Adjust. Refer to the

CHI PANEL

OPERATION

bulletin,

Adjustment

section,

Inlet Section Adjustments

procedure.

•

Flatwork Pieces Overlap

1. GAP settings need adjust-

ment.

Adjust. Refer to the

CHI PANEL OP-

ERATION

bulletin,

Adjustment

sec-

tion,

CHI Adjustments

procedure.

•

2. Tail sensors may be dirty,

misaligned, or defective.

Clean/adjust/replace as necessary. For

more information within this chapter,

refer to

Sensor Function

section.

•

3. PE23 Gap/Exit Sensor

problem?

Leading Edge of Flatwork

Folded Over

1. The corners are too long.

Check sensor alignment in front of

clutch rolls. Refer to the

REPAIR

chap-

ter,

Sensors

section,

Roll Photosen-

sor Alignment

procedure.

Adjust CORNER STOP DLY. Refer to

the

CHI PANEL OPERATION

bulletin,

Adjustment

section,

Inlet Adjust-

ments (INL)

procedure.

•

2. Mechanical problem with

the spread clamp or its air

cylinder.

Check/adjust. Refer to the

REPAIR

chapter,

Spread Section

section,

Spreader Clamp Mechanical Adjust-

ment

procedure.

•

3. The lower spreader belt

speed may need adjust-

ment.

Adjust. Refer to the

CHI PANEL

OPERATION

bulletin,

Adjustment

section,

Program Adjustments (CHI)

procedure. Note for optimum accuracy,

set this time to 0 to activate the roller

sensors.

•

6.8 Discharge Section

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды