Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 53 / 288

Edge MAXX

Operating Guidelines

3-13

Speed Control

If the unit is equipped with Chicago’s speed

interlock system, the speed setting can be changed

to automatic mode. When in automatic mode,

the unit will match any changes in speed that the

ironer makes.

Automatic Speed Operation

On the CHI Panel, press the CURSOR

key until the ﬂashing cursor is under the

speed display.

Press the ENTER key. The CHI Panel

display changes to show the machine is

now operating in automatic mode.

Press the ENTER key again to switch back

to manual speed control.

Manual Speed Operation

As a general rule, the spreader/feeder speed

should be slightly slower than the ironer’s speed,

usually by up to 5 fpm (1.5 mpm).

If the spreader/feeder is too fast, the ﬂatwork

will bunch as it feeds into the ironer. If the speed

is set too slow, the ﬂatwork will be excessively

stretched.

When the unit is operating in manual speed

mode, press the CURSOR key to move the

ﬂashing cursor under the speed display.

As appropriate, press the SPEED



button

to increase speed or the SPEED



button

to decrease speed.

Counter Operation

The CHI Panel automatically tracks the large

count totals for each program and for all pieces

processed. To view the counts:

Press the CURSOR key until the ﬂash-

ing cursor is under the value for count

(CNT).

Press ENTER to see the total counts for

the units as well as the count for each

program.

For more information regarding counter

displays and operation, refer to the

CHI PANEL

OPERATION

bulletin,

Operation

section,

Counters

subsection.

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды