Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 130 / 288

Troubleshooting

Edge MAXX

6-28

WARNING

Only trained personnel with experience

in electrical or mechanical repair should

troubleshoot and repair the unit.

Troubleshooting

WARNING

Read the

REPAIR

chapter and make

sure that the power is disconnected

before doing any repairs.

6.12 Compressed Air System

ISSUE

POSSIBLE CAUSE

SOLUTION

No Air Supply to Unit

1. Facility air supply is off.

Turn facility air supply is on.

Open air supply valve to unit.

•

2. Air supply hose to unit is

disconnected or clogged.

Make sure compressed air connection

to unit is secure.

Check supply hose and clear of any

obstructions.

•

Poor Air Pressure in Unit

1. Check air pressure regula-

tor settings.

Make sure incoming air pressure is at

least 80 psi (550 kPa).

Pressure must be set correctly. Refer

to the

OPERATING PRINCIPLES

chapter,

Compressed Air System

section,

Air Filter/Regulators

subsec-

tion.

•

2. Air ﬁlter/regulator/auto

drain is dirty.

Service. Refer to the

PREVENTIVE

MAINTENANCE

chapter,

Semi-Annu-

al PM

section,

Clean Air Filter/Regu-

lator/Auto Drain

procedure.

•

3. Air supply pressure to unit

too low.

Check facility air pressure. Adjust/cor-

rect as necessary to meet unit re-

quirements. Refer to the

APPENDIX

Technical Speciﬁcations

•

4. Air supply hose/piping too

small.

Make sure supply lines are 1/2” (13

mm) inside diameter.

•

5. Air supply hose to unit is

leaking, kinked or plugged.

Check hose to unit. Repair/replace as

necessary.

•

No or Poor Air Supply to Air

Devices

1. Compressed air tubing

problem.

Make sure connections are secure.

Check tubing for leaks, kinks or plugs.

•

2. Air valve malfunction.

Make sure coil is properly connected

to air valve.

Make sure coil is receiving electrical

signal.

Replace coil/air valve.

•

3. Air supply hose/piping too

small.

Make sure supply lines are 1/2” (13

mm) inside diameter.

•

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды