Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 42 / 522

background image

2 - SAFETY INFORMATION

Support strut and service link

Support strut

WARNING

Crushing hazard!
If you service the machine with the loader lift arms raised, always use the support strut. Remove the
support strut from the storage position and place the strut onto the cylinder rod. Install the retaining
bolt entirely into the strut. Lower lift arms onto the support strut.
Failure to comply could result in death or serious injury.

W0140A

If you service the machine with the loader lift arms raised, always use the support strut.

1. Empty the loader bucket, raise the loader lift arms to

approximately

2.1 m

(

7 ft

) and stop the engine.

2. Maintain the bucket in a dumped position. Remove

the retaining bolt

(1)

. Remove the support strut

(2)

from the storage position.

3. Place the support strut

(2)

on the cylinder rod with the

guide lock tab on top of cylinder and pointing toward
the bucket.

4. Install the retaining bolt

(1)

entirely into the support

strut

(2)

using all threads.

5. Slowly lower the lift arms onto the support strut. Main-

tain the bucket in a dumped position.

LEIL15WHL1850AA

1

NOTE:

support strut in transport position.

RCPH10WHL061BAL

2

NOTE:

support strut in service position.

If you do not follow this procedure, you can cause death or serious injury if the loader lift arms are lowered unexpect-
edly.

2-12

«
...
40
41
42
43
44
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

Бренд: Vestil Страницы: 17

Бренд: BARKO LOADERS Страницы: 112

Бренд: Toro Страницы: 8

Бренд: Toro Страницы: 8

Бренд: Toro Страницы: 12

Бренд: Toro Страницы: 16

Бренд: Toro Страницы: 20

Бренд: AVANT Страницы: 16

Бренд: AVANT Страницы: 24

Бренд: AVANT Страницы: 24

Бренд: AVANT Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды