Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 228 / 522

background image

6 - WORKING OPERATIONS

Coupling to the attachment

WARNING

Falling object hazard!
Before starting the machine, make sure the coupler switch is in the locked position.
Failure to comply could result in death or serious injury.

W0931B

WARNING

Falling object hazard!
Always visually inspect coupler locking pins for proper engagement. An improperly locked attach-
ment could release and fall.
Failure to comply could result in death or serious injury.

W0930A

WARNING

Avoid injury and/or machine damage!
Before operating the machine, make sure the attachment is securely connected to the machine. Apply
downward pressure with the bucket to the ground to make sure the coupler connection is secure.
Failure to comply could result in death or serious injury.

W0932A

1. Locate the coupler engagement button on the right-

hand console of operator’s compartment. When the
coupler locking pins are extended, the green light on
this button is on.

2. Press and hold (about

3 s

) the coupler engagement

button to retract the locking pins. The display shows
the message “Coupler pins Disengaging” and the pins
start to move. Once the locking pins are fully retracted,
the green light goes out and the red light illuminates.
The display shows the message “Coupler pins Disen-
gaged”.
Do not engage the attachment with the locking pins
extended.

LEIL16WHL1125AA

1

3. Situate the machine with upper male portion of the

coupler aligned with the upper female portion of the
attachment the operator wishes to couple. Position the
front of the coupler into the attachment as shown.

LEIL16WHL0038AA

2

6-6

«
...
226
227
228
229
230
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

Бренд: jcb Страницы: 16

Бренд: Legend Страницы: 41

Бренд: Gehl Страницы: 82

Бренд: Gehl Страницы: 112

Бренд: Gehl Страницы: 170

Бренд: Gehl Страницы: 206

Бренд: Gehl Страницы: 208

Бренд: AVANT Страницы: 18

Бренд: AVANT Страницы: 18

Бренд: AVANT Страницы: 28

Бренд: AVANT Страницы: 40

Бренд: AVANT Страницы: 36

Бренд: AVANT Страницы: 40

Бренд: AVANT Страницы: 40

500 Series 2019

Бренд: AVANT Страницы: 64

Бренд: AVANT Страницы: 84

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды