Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 97 / 522

background image

3 - CONTROLS AND INSTRUMENTS

Steering column

WARNING

Hazard to bystanders!
Always sound the horn before starting the machine. Make sure the work area is clear of other persons,
domestic animals, tools, etc. before you operate the machine. Never allow anyone in the work area
during machine operation.
Failure to comply could result in death or serious injury.

W0304A

Right-hand multifunction lever

1. Horn
Push the horn button in to actuate the horn.

2. Turn signal lever
Push the control lever up to signal a left
turn. Pull the lever down to signal a right
turn. Move the lever manually to the center
position to stop the signals.

3. High beam headlights and flashing
Pull the multifunction lever to turn on
the high beam headlights. Push the
multifunction lever for flashing.

4. Driving light wheel
Rotate the wheel

(4)

to set one of the three

positions:
0 – Lights OFF
1 – Marker/position lights
2 – Low beam headlights

5. Front wiper/washer wheel
Rotate the wheel

(5)

to set one of the four

positions:
0 - OFF position.
I - ON position – Rotate clockwise the wheel

(5)

to the first position to activate the front

wiper.
L - INTERMITTENT - Rotate clockwise the
wheel

(5)

to the second position to activate

the front wiper at the intermittent speed.
H - CONTINUOUSLY - Rotate clockwise
the wheel

(5)

to the third position. The front

wiper runs continuously.
WASH - Rotate counterclockwise and hold
the wheel

(5)

for washer fluid.

6. Front wiper speed wheel
Rotate the wheel

(6)

to adjust and set the

front wiper intermittent speed. There are
six settings for the front wiper intermittent
speed.

LEIL16WHL0542AB

1

3-13

«
...
95
96
97
98
99
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

Бренд: Toro Страницы: 8

Бренд: Toro Страницы: 8

Бренд: Toro Страницы: 12

Бренд: Toro Страницы: 16

Бренд: Toro Страницы: 20

Бренд: Toro Страницы: 12

Бренд: Toro Страницы: 28

Бренд: Takeuchi Страницы: 235

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды