Case 721G Stage IV Скачать руководство пользователя страница 229

Страница: 229 / 522

6 - WORKING OPERATIONS

4. Roll back the coupler with attachment to align the at-

tachment pin holes with coupler locking pins.

LEIL15WHL1831AA

5. Press the coupler engagement button to extend the

locking pins. Once the locking pins are fully extended,
the red light goes out and the green light turns on.

6. Maintain the coupler in rollback position. Position the

red coupler locking visual indicators

(1)

in your full field

of view. Verify and ensure the coupler locking pins

(2)

are fully extended.

LEIL16WHL1339AA

7. Lower the attachment and roll the front end toward

the ground. Apply downward pressure to ensure the
attachment is securely locked.

LEIL16WHL0039AB

6-7

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Результаты поиска

Содержание 721G Stage IV

Отзывы:

Бренды по названию

Популярные бренды

Case 721G Stage IV, Руководство оператора

Результаты поиска

Содержание 721G Stage IV

Отзывы:

Бренды по названию

Популярные бренды