Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 245 / 522

background image

7 - MAINTENANCE

• Biodiesel oxidation, which can lead to the formation of

deposits that can harm the fuel injection system.

NOTICE:

Any problem in the engine fuel injection equip-

ment associated with non-compliance to the following
conditions for biodiesel fuel handling and maintenance
will not be covered for Warranty by CASE CONSTRUC-
TION.

Purchase biodiesel fuel from a trusted supplier who
understands the product and maintains acceptable fuel
quality.

The use of biodiesel blends up to B7 will not void
the CASE CONSTRUCTION warranty as long as the
following conditions for biodiesel fuel handling and main-
tenance are stringently followed:

Biodiesel fuel must be pre-blended by the supplier. Mixing
biodiesel fuels on-site can result in an incorrect mixture
that could damage the engine and/or fuel system.

NOTICE:

CASE CONSTRUCTION may void your war-

ranty if the problem is associated with poor fuel quality
due to improper blending. It is the responsibility of the
fuel supplier and/or yourself to ensure the right type of
fuel and blend is delivered and used.

Storage

The machine should not be stored for more than 6 months
with biodiesel in the fuel system. For longer storage time,
it is strongly suggested that only regular

EN 590

or #2

diesel fuel is used.

NOTE:

If storage for longer than 6 months is necessary,

the engine must be run on regular

EN 590

or #2 diesel for

a minimum of 20 hours to flush the biodiesel fuel out of
the fuel system prior to storage.

Biodiesel is highly hygroscopic and tends to collect water
more than diesel fuel. This increases the risk of algae
and bacteria growth which can cause severe damage to
the fuel injection system. Keep the machine fuel tanks
and on-site storage tanks as full as possible to limit the
amount of air and water vapors inside the tank. Drain
water from the tanks at least once a week.

NOTICE:

Use only CASE CONSTRUCTION approved

biocide additives on Tier 4B (final), Stage IV and Stage
V engines with an exhaust aftertreatment system.

7-7

«
...
243
244
245
246
247
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

Бренд: Baoli Страницы: 112

Бренд: Bush Hog Страницы: 96

Бренд: Wacker Neuson Страницы: 61

Бренд: jcb Страницы: 26

Бренд: Giant-Vac Страницы: 12

Бренд: diamond mowers Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды