Case 721G Stage IV Скачать руководство пользователя страница 321

Страница: 321 / 522

7 - MAINTENANCE

4. Extract the main filter element

(1)

from the filter housing

(2)

NOTE:

if the main filter element looks very dirty and no

longer fit for purpose, proceed directly with the replacement
(refer to

7-114

LEIL15WHL0567AB

5. Clean the main filter element with compressed air

(maximum

5 bar

(

72.5 psi

)) carefully, applying the

compressed air from the clean side (seal side) until no
more dust is blown out. The tip of the compressed air
gun must not touch the filter.

NOTICE:

never wash out or beat the main filter element.

NOTICE:

when blowing clean, ensure no dust gets into the

inside of the main filter element.

LEIL17WHL1650AA

6. Check the cleaned main filter element thoroughly for

signs of damage to the filter paper and seals.

7. Reinstall the main filter element into the filter housing.

8. Secure the filter grid assembly to the filter housing.

9. Close the right-hand door.

7-83

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Результаты поиска

Содержание 721G Stage IV

Отзывы:

Бренды по названию

Популярные бренды

Case 721G Stage IV, Руководство оператора

Результаты поиска

Содержание 721G Stage IV

Отзывы:

Бренды по названию

Популярные бренды