Case 721G Stage IV Скачать руководство пользователя

Страница: 378 / 522

7 - MAINTENANCE

4. Remove the rubber boot cover from the wires of

the liquid level/temperature sensor sending unit

DEF/A

LUE

and engine coolant supply lines. Mark

wire and hose connection positions.

RCPH11WHL704BAU

5. Unplug the wiring harness.

RCPH11WHL705BAU

6. Disconnect the engine coolant lines

(1)

and the

DEF/ADBLUE® lines

(2)

by pushing coupling together,

squeezing the tabs and then pulling the connection
apart.
Remove the vent line

(3)

by pushing collar down with

screwdriver and pulling up on the vent line

(3)

NOTE:

plug all lines to prevent debris from entering the

system.

LEIL16WHL1567AB

7. Move the wiring harness, the engine coolant lines, the

DEF/A

LUE

supply/return lines and the vent line, off

to the side.

RCPH11WHL706BAU

7-140

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Результаты поиска

Содержание 721G Stage IV

Отзывы:

Похожие инструкции для 721G Stage IV

Бренды по названию

Популярные бренды

Case 721G Stage IV, Руководство оператора

Результаты поиска

Содержание 721G Stage IV

Отзывы:

Похожие инструкции для 721G Stage IV

Бренды по названию

Популярные бренды