Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 253 / 522

background image

7 - MAINTENANCE

If hydraulic fluid seeps into the ground, the machine owner
and the authorities responsible must be informed.
PANOLIN HLP SYNTH VG 46 is suitable only for use in
hydraulic systems.
As PANOLIN HLP SYNTH VG 46 is not soluble in water,
condensed water may be deposited in the hydraulic fluid
tank.
Condensed water must therefore be drained off at regular
intervals and after lengthy downtimes, then disposed of in
the same way as used oil.
Use only PANOLIN HLP SYNTH VG 46 for changing or
topping up the hydraulic fluid.
The hydraulic fluid may not be mixed with hydraulic fluids
or hydraulic fluids from other manufacturers, as this re-
duces its biodegradability.
Operating equipment and attachments operated with min-
eral hydraulic fluid must not be mounted until thoroughly
emptied, cleaned, and flushed.
Analysis will show whether the hydraulic fluid can be used
beyond the standard changing intervals.
See also

Hydraulic systems - Check

.

Transmission component oil

Extreme pressure oil must be used for enclosed trans-
mission components. Choose an oil that is manufactured
for your climate/temperature conditions such as

CASE

AKCELA NEXPLORE™ FLUID

. See the charts at the be-

ginning of this section.

Front and rear axle oil

Extreme pressure oil must be used for enclosed axle com-
ponents. Choose an oil that is manufactured for your
climate/temperature conditions such as

CASE AKCELA

TRANSAXLE FLUID 80W-140

.

Grease

CASE AKCELA MOLY GREASE

.

Environment

Before you service this machine and dispose of oil, fluids,
and lubricants, obey environmental regulations. Do not
drain oil or fluids on to the ground or into containers that
leak. Check with your local environmental, recycling cen-
ter or your dealer for correct disposal information.

7-15

«
...
251
252
253
254
255
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

Бренд: Toro Страницы: 8

Speed King Drive Over- Pit

Бренд: CrustBuster Страницы: 24

Telehandler TH412

Бренд: Wacker Neuson Страницы: 362

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды