Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 38 / 522

background image

2 - SAFETY INFORMATION

Fuel handling

• Do not smoke or permit open flames while fueling or

near fueling operations.

• Never remove the fuel cap or refuel machines with the

engine running or the engine hot. Never allow fuel to
spill on hot machine components. Avoid spilling fuel on
the ground or contaminating the environment.

• Always maintain control of the fuel filler nozzle when

filling the tank. This will help avoid spilling fuel.

• Clean up spilled fuel immediately and dispose of all

contaminated material in an environmentally correct
manner.

• Tighten the fuel tank cap securely. If you lose the fuel

cap, replace it only with the manufacturer's approved
cap. Use of a non-approved cap without proper venting
may result in pressurization of the tank.

• Never use gasoline for cleaning purposes.

• Use the correct fuel for the operating season.

Handling

D

IESEL

E

XHAUST

F

LUID

(DEF)/

A

D

B

LUE

®

• Your machine is equipped with additional components

to comply with national and local exhaust emissions re-

quirements. Diesel exhaust fluid or

DEF/A

D

B

LUE

®

is a

non-toxic aqueous urea solution. It chemically reduces
NOx emissions from heavy duty diesel powered ma-
chines. It is neither explosive nor considered harmful
to the environment and is classified under the minimum
risk category of transportable fluids.

• Personal Protection Equipment (PPE) is not required

under normal conditions. If splashing is likely, wear eye
protection.

• For prolonged or repeated contact, impervious gloves

are recommended.

• Clean up spilled fluid immediately and dispose of all

contaminated material in an environmentally correct
manner.

• Follow the precautions listed in this safety information

chapter when handling any service fluid.

•

DEF/A

D

B

LUE

®

must be stored in clean, sealed contain-

ers.

• Make sure that no debris enters the machine

DEF/A

D

B

LUE

®

tank. Clean the

DEF/A

D

B

LUE

®

tank

cap and the surrounding area before opening.

• Fill the

DEF/A

D

B

LUE

®

tank using clean filling equip-

ment with the correct length and diameter nozzle.

2-8

«
...
36
37
38
39
40
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

Бренд: Case Страницы: 22

Бренд: Case Страницы: 22

Бренд: Topcon Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды