Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 177 / 522

background image

4 - OPERATING INSTRUCTIONS

Starting the engine

WARNING

Equipment failure could cause accident or in-
jury!
Before operating the machine, check for cor-
rect operation of steering, brakes, hydraulic
controls, instruments, and safety equipment.
Make sure the transmission control lever is in
the neutral position. Make all adjustments be-
fore operating the machine.
Failure to comply could result in death or se-
rious injury.

W0204A

NOTE:

if the machine has been out of use for some time,

see “Removal” - Chapter 7 in this manual.

NOTE:

if you need to start the engine using a booster bat-

tery, see “Auxiliary battery connections - Check” - Chapter
7 in this manual.

1. Turn the timed disconnect switch to the ON position.

2. Take up the correct position in the operator's seat with

the seat belt correctly fastened. Make sure you can
push the foot pedals completely down with your back
against the seat cushion.

3. Make certain the transmission direction control is in

NEUTRAL and the parking brake is applied.

4. Turn the key switch to the ON position and check the

instrument indicators.

5. Keep all non-authorized personnel clear of the area.

Sound the horn to alert others of your intent to start
the engine. Turn the key switch to the START position
until the engine starts, then release the key.

NOTICE:

the starter has an automatic cut-out to pro-

tect itself. In cold weather conditions, extended crank-
ing may be necessary.

6. After the engine starts, check the instruments to make

sure the indications are correct. Run the engine at low
idle with the transmission in NEUTRAL until the engine
coolant temperature is warm.

NOTICE:

operate the machine at reduced loads until

all systems reach operating temperature. This is very
important during extremely cold weather operation to
protect both the engine and hydraulic systems.
The transmission will not shift into gear unless the
transmission fluid is warm enough.

Engine speed

DO NOT OPERATE the engine at idle speed for long peri-
ods. This can cause a low operating temperature. A low
operating temperature can cause acids and deposits in
the engine oil.

Run the engine at low idle for a minute at start up before
picking up speed and load.

NOTICE:

always bring the engine to low idle for a few

minutes to let all parts cool evenly before shut down.

4-3

«
...
175
176
177
178
179
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

Бренд: jcb Страницы: 16

Бренд: Kubota Страницы: 112

Бренд: jcb Страницы: 51

Бренд: Case Страницы: 252

MINI SKID TASKMASTER Series

Бренд: RAMROD Страницы: 37

Бренд: P.Lindberg Страницы: 123

Бренд: Komatsu Страницы: 41

Бренд: Komatsu Страницы: 43

Бренд: Komatsu Страницы: 51

Бренд: Komatsu Страницы: 284

Бренд: Komatsu Страницы: 440

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды