Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 176 / 522

background image

4 - OPERATING INSTRUCTIONS

Starting the unit

Starting the engine

WARNING

IMPROPER OPERATION OF THIS MACHINE CAN CAUSE DEATH OR SERIOUS INJURY.
MAKE SURE THAT EVERY OPERATOR:
-is instructed in the safe and proper use of this machine.
-reads and understands the operator's manual for this machine.
-reads and understands ALL safety signs on the machine.
Failure to comply could result in death or serious injury.

W0188A

Before operating the machine

Before operating this machine, complete the following
procedures:

1.

Check the level of all fluids (engine oil, fuel, transmis-
sion oil,

DEF/A

D

B

LUE

®

, hydraulic fluid, and coolant)

and make sure that the fluids and lubricants are suit-
able for prevailing conditions.

2.

Carry out the daily maintenance operations.

3.

Inspect the machine, look for any signs of possible
leakage and check the hoses. Tighten or replace as
necessary.

4.

Check the tires for any visible damage. Replace or
repair as necessary. Check for correct tire air pres-
sure and adjust the pressure if necessary.

5.

Clean the steps and hand holds. Grease, oil, mud,
or ice in winter on the steps and access handles can
cause accidents. Keep the steps and the access
handles clean at all times.

6.

Clean or replace any decals which are illegible. See
“Safety signs” - Chapter 2 in this manual for further
information.

7.

Make sure that the engine access panels and all
doors are properly closed and latched.

8.

Secure the cab door in either fully closed or fully
opened position.

9.

Remove any obstructions which hinder visibility.
Clean the windshield, the windows and the rear view
mirrors, and backup camera lens.

10. Check that no tools or other items have been left on

the machine or in the operator's compartment.

11. Make sure no one is on or under the machine. The

operator must be alone on the machine.

12. Make sure no one is standing in the machine working

area.

13. Find out about current safety measures in use on the

work site.

14. Work out a convenient means of escape from the

machine (emergency exit via the windshield, the rear
or side window glass) in the event of the cab door
being jammed or the machine turning over.

15. Before undertaking any travel or working operations

during hours of darkness, make sure the lighting and
signaling equipment are fully operative.

16. Adjust the seat so that you can apply the foot brakes

when your back is against the seat backrest.

17. Fasten and adjust the seat belt.

18. With the engine running and at operating tempera-

ture, check the instrument panel for correct indica-
tions.

19. Check the loader controls for correct operation.

4-2

«
...
174
175
176
177
178
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

Бренд: TEXIO Страницы: 167

Бренд: jcb Страницы: 51

Бренд: Mertz Страницы: 84

Бренд: Toro Страницы: 36

Бренд: Toro Страницы: 44

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды