Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 277 / 522

background image

7 - MAINTENANCE

Cold weather handling

• Your machine is equipped with an internal tank heater to thaw frozen

DEF/A

D

B

LUE

®

. Your machine will still function

until the

DEF/A

D

B

LUE

®

begins to flow. The SCR system will then function normally.

NOTE:

you may notice a slight reduction in engine torque in high demand situations until the

DEF/A

D

B

LUE

®

is fully

thawed.

• Do not heat

DEF/A

D

B

LUE

®

for long periods of time at temperatures above

30 °C

(

86 °F

). This causes the solution

to decompose, which very slowly decreases the expected shelf life.

NOTICE:

do not use an anti-gelling or freeze point improver in your

DEF/A

D

B

LUE

®

. The

32.5%

solution is specifically

designed to provide the optimum NO

x

reduction properties. Any further blending or adjusting of the

DEF/A

D

B

LUE

®

mixture will lessen its ability to perform correctly and may cause damage to the SCR components.

Handling and supply of additives

• Personal Protective Equipment (PPE) is not required under normal conditions. If splashing is likely, wear eye pro-

tection. For prolonged or repeated contact, impervious gloves are recommended. Follow the precautions listed in
the SAFETY INFORMATION chapter when handling any service fluid.

• No additives are required.

NOTICE:

contaminated

DEF/A

D

B

LUE

®

can affect the performance of your machine. Follow all instructions in this

manual when handling

DEF/A

D

B

LUE

®

.

Shelf life

Constant ambient storage temperature

Minimum shelf life

Less than or equal to

10 °C

(

50 °F

)

36 months

Less than or equal to

25 °C

(

77 °F

) ¹

18 months

Less than or equal to

30 °C

(

86 °F

)

12 months

Less than or equal to

35 °C

(

95 °F

)

6 months

Greater than

35 °C

(

95 °F

)

-²

¹ To prevent decomposition of

DEF/A

D

B

LUE

®

, avoid prolonged transportation or storage above

25 °C

(

77 °F

).

However, temporary exposure to higher temperatures does not necessarily influence the quality of

DEF/A

D

B

LUE

®

.

² Significant loss of shelf life: check every batch before use. See your authorized dealer for more information
on testing.

NOTE:

the main factors taken into account to define the shelf life in the table above are the ambient storage tempera-

ture and the initial alkalinity of

DEF/A

D

B

LUE

®

. The difference in evaporation between vented and non-vented storage

containers is an additional factor.

NOTE:

the information in this table is for reference only and has been provided by the International Organization for

Standardization, Document number ISO 22241-3 Diesel engines - NO

x

reduction agent AUS 32 - Part 3: Handling,

transportation and storage.

NOTE: DEF/A

D

B

LUE

®

that remains in the tank of the machine after the season does not require any special precau-

tions unless storage exceeds the shelf life table above.

Disposal

• Dispose of

DEF/A

D

B

LUE

®

and any filter accumulations in accordance with all applicable laws governing waste

disposal.

7-39

«
...
275
276
277
278
279
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

Бренд: Hitachi Страницы: 51

Бренд: ahlmann Страницы: 103

Бренд: ahlmann Страницы: 113

Бренд: New Holland Страницы: 8

Бренд: New Holland Страницы: 31

Бренд: New Holland Страницы: 41

Бренд: New Holland Страницы: 41

Бренд: HYTEC Страницы: 52

FORKLIFT 5FD 7 0-30 Series

Бренд: Toyota Страницы: 71

Бренд: jcb Страницы: 149

Бренд: Toro Страницы: 52

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды