Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 406 / 522

background image

7 - MAINTENANCE

Auxiliary battery connections - Check

WARNING

Improper operation or service of this machine can result in an accident.
An error connecting auxiliary starting cables or short-circuiting battery terminals can cause an acci-
dent. Connect auxiliary starting cables as instructed in this manual.
Failure to comply could result in death or serious injury.

W0263A

DANGER

Explosion hazard!
Read "Connecting booster battery" procedure completely before attempting to jump-start or service
a battery.
Failure to comply will result in death or serious injury.

D0086A

WARNING

Explosion hazard!
Booster batteries or jumper cables must be connected properly to prevent battery explosion and/or
damage to the electrical system. Connect positive to positive and negative to negative.
Failure to comply could result in death or serious injury.

W0343A

Make sure that the voltage of the booster batteries (

12 V

each battery) is the same as that of the machine

system (

24 V

). The batteries are located on the left-

hand side of the machine.

1. Turn off the ignition and all accessories on the machine.

Remove the battery cover from left-hand side of the
machine. Remove the battery terminal covers.

2. Identify the discharged battery.

3. Connect one end of the positive (+) cable to the positive

(+) terminal on the booster battery. Connect the other
end of the positive (+) cable to the positive (+) terminal
of the discharged battery.

4. Connect the negative (-) cable to the negative (-) termi-

nal on the booster battery.

5. Connect the other end of the negative cable to the en-

gine block or frame of the machine with the discharged
battery. Do not connect to the negative terminal on the
battery.

NOTICE:

do not connect the other end of the negative ca-

ble to sheet metal or any rotating part, as damage can re-
sult.

6. Start the engine.

7. Remove the booster battery negative (-) cable from the

machine, then from the booster battery. Remove the
positive (+) cable from the machine and then from the
booster battery.

8. Install the terminal covers.

LEIL16WHL1518AA

1

7-168

«
...
404
405
406
407
408
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

MT 625 H 75K COMFORT ST5 S1

Бренд: Manitou Страницы: 136

TASKMASTER 1350 PRO Series

Бренд: RAMROD Страницы: 37

Бренд: ELTRA Страницы: 35

Бренд: diamond mowers Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды