Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 157 / 522

background image

3 - CONTROLS AND INSTRUMENTS

5. Low fuel level (orange)

The indicator illuminates when the tank is almost empty.

6. Parking brake indicator (red)

This indicator illuminates when the parking brake is applied.

7. Stop master indicator (red, critical)

The Stop Master Indicator is a critical
warning display. See the “Critical warnings”
table. When the Stop Master indicator
illuminates, IMMEDIATELY bring the
machine safely to a stop, and turn the
engine OFF. Failure to do so may result
in personal injury and/or damage to the
machine.

The following table lists critical warning displays that may appear on the multifunction display and the corrective action
that is required. Should a fault occur, a continuous audible alarm will sound and the Stop Master Indicator will be RED.
A warning message will be displayed in the message area.

Critical warnings

Display

Description

Corrective Action

Engine oil
pressure

Low engine oil
pressure

Bring the machine to a safe stop, and turn the engine OFF immediately.
Contact your dealer.

Brake
pressure

Low brake pressure

Bring the machine to a safe stop, and turn the engine OFF immediately.
Contact your dealer.

Steering
pressure
(w/auxiliary
steering)

Low steering pressure

Bring the machine to a safe stop, and turn the engine OFF immediately.
Contact your dealer.

Coolant
temperature

High engine coolant
temperature

Bring the machine to a safe stop, and turn the engine OFF immediately.
Check the coolant levels after allowing the engine and the coolant to cool.
Contact your dealer.

Hydraulic oil
temperature

High hydraulic oil
temperature

Bring the machine to a safe stop, and turn the engine OFF immediately.
Contact your dealer.

Transmission
oil temperature

High transmission oil
temperature

Bring the machine to a safe stop, and turn the engine OFF immediately.
Contact your dealer.

Poor

DEF/

A

D

B

LUE

®

Quality

Detected,

Power Limited

Moderate engine
power loss has begun,
up to

65%

torque

reduction and

40%

engine speed within

40 min

of engine

running time.

DEF/A

D

B

LUE

®

quality/concentration is questionable. Drain the tank and

discard the

DEF/A

D

B

LUE

®

. Fill with new

DEF/A

D

B

LUE

®

.

NOTE:

see “

DEF/A

D

B

LUE

®

tank refilling” section for important tank draining

information.

DEF/A

D

B

LUE

®

Injection Failed

Power Limited

SCR fault/failure
detected. Up to

65%

torque reduction and

40%

engine speed

reduction within

40 min

.

Contact your local authorized dealer for repair.

3-73

«
...
155
156
157
158
159
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

Бренд: New Holland Страницы: 1

Бренд: Komatsu Страницы: 31

Бренд: SDLG Страницы: 109

Бренд: SDLG Страницы: 113

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды