Case 721G Stage IV Скачать руководство пользователя | Manualshive

Страница: 336 / 522

background image

7 - MAINTENANCE

Roll Over Protective Structure (ROPS) - Check

WARNING

Roll-over hazard!
After an accident, fire, tip over, or roll over, a qualified technician MUST replace the Roll-Over Protec-
tive Structure (ROPS) before returning the machine to the field or job site operation.
Failure to comply could result in death or serious injury.

W0134A

WARNING

Misuse hazard!
Your machine is equipped with an operator protective structure. DO NOT weld, drill holes, attempt
to straighten, or repair the protective structure. Modification in any way can reduce the structural
integrity of the structure.
Failure to comply could result in death or serious injury.

W0001B

Check and inspect the ROPS structure and the seat restraint system every 500 hours of operation.

Your machine is equipped with an operator Protec-
tive Structure, such as: Rollover Protective Structure
(ROPS) or Falling Object Protective Structure (FOPS).
A ROPS may be a cab frame or a two-posted or
four-posted structure used for the protection of the
operator to minimize the possibility of serious injury.
The mounting structure and fasteners forming the
mounting connection with the machine are part of the
ROPS. The Protective Structure is a special safety
component of your machine.

DO NOT attach any

device to the Protective Structure for pulling purposes.
DO NOT drill holes into the Protective Structure. The
Protective Structure and interconnecting components
are a certified system. Any damage, fire, corrosion
or modification will weaken the structure and reduce
your protection. If this occurs, the Protective Structure
MUST be replaced so that it will provide the same
protection as a new Protective Structure. Contact your
dealer for Protective Structure inspection and replace-
ment. The mounting or suspension for the Protective
Structure, operator seat and suspension, seat belts
and mounting components and wiring within the oper-
ator’s protective system MUST be carefully inspected
for damage. All damaged parts MUST be replaced.

ROPS identification plate

The wheel loader has a ROPS identification plate
showing the certification of the ROPS, gross weight,
approval, regulation, and model number of the ma-
chine.
The ROPS identification plate is located under the op-
erator’s seat at the left-hand side.

LEIL16WHL1167AB

1

7-98

«
...
334
335
336
337
338
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для 721G Stage IV

Бренд: Takeuchi Страницы: 267

TITAN CITY HOOKLOADER

Бренд: HYVA Страницы: 22

Бренд: SDLG Страницы: 109

Бренд: SDLG Страницы: 113

Бренд: Gehl Страницы: 82

Бренд: Gehl Страницы: 112

Бренд: Gehl Страницы: 170

Бренд: Gehl Страницы: 206

Бренд: Gehl Страницы: 208

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды