Case 721G Stage IV Скачать руководство пользователя страница 312 | Manualshive

Страница: 312 / 522

Case 721G Stage IV Скачать руководство пользователя страница 312

7 - MAINTENANCE

Every 100 hours

Machine fittings - Grease

WARNING

Improper operation or service of this machine can result in an accident.
Read and understand the SAFETY INFORMATION Section before you perform any maintenance, ser-
vice, or repairs. Read and understand the specific service procedures for the components you plan
to work with before you start servicing the machine.
Failure to comply could result in death or serious injury.

W0138A

DANGER

Crushing hazard!
If you service the machine with the loader lift arms raised, always use the support strut. Remove the
retaining pin and place the support strut onto the cylinder rod. Install the retaining pin into the support
strut. Lower the lift arms onto the support strut.
Failure to comply will result in death or serious injury.

D0084A

WARNING

Avoid injury! Always do the following before lubricating, maintaining, or servicing the machine.
1. Disengage all drives.
2. Engage parking brake.
3. Lower all attachments to the ground, or raise and engage all safety locks.
4. Shut off engine.
5. Remove key from key switch.
6. Switch off battery key, if installed.
7. Wait for all machine movement to stop.
Failure to comply could result in death or serious injury.

W0047A

Grease the articulation joint, machine grease fittings, lift arm fittings and lift arm cylinder every 100 hours of operation
or sooner if conditions so require.

Prior operation:

Keep all non-authorized personnel clear of the area. Park the machine on a firm, level surface in neutral with the
parking brake applied. Lower the bucket/attachment to the ground. Turn off the engine. Install the transport/service
link into the locked position.

Prior operation:

Make sure all residual pressure is relieved from the circuits before beginning maintenance.

Service specifications

Grease

CASE AKCELA MOLY GREASE

NOTE:

if the machine (Z-bar or XR version) is equipped with automatic lubrication system, you do not need to perform

following instructions.

Clean around the area to be greased before service.

NOTE:

in severe conditions, such as immersion in water, it may be necessary to reduce the greasing service intervals.

7-74

«
...
310
311
312
313
314
...
»

Содержание 721G Stage IV











































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды