BONFIGLIOLI Vectron Active Cube Скачать руководство пользователя страница 173

Страница: 173 / 240

14.3

Non motion control configurations

In non motion control configurations (Parameter

Configuration

30 ≠ x40), object

0x6060

modes of operation

is fixed to “2”

velocity mode. Object

0x6061

modes of

operation display

is always “2”

velocity mode. This cannot be changed.

Related objects:

Control word

Status word

Target velocity

Velocity demand

Control effort

Velocity min max amount

0x6048

Velocity acceleration

0x6049

Velocity deceleration

0x604A

Velocity quick stop

The Ramp Rise/Fall times are set up via parameters 430…433.

14.3.1

Behavior in quick stop

In quick stop, the parameters

Switch-off threshold

637 (percent of fmax) and

Hold-

ing time

638 (holding time after falling short of the switch-off threshold) are relevant.

In a quick stop the drive is shutdown via the emergency stop ramps. The emergency

ramps are set up via Object

0x604A

Velocity Quick Stop

or parameters

Emergency

stop clockwise

424 and

Emergency stop anti-clockwise

425.

If frequency/speed zero has been reached during the holding time, the drive contin-

ues to be supplied with direct current until the switch-off time has expired. With this

measure, there is an assurance that the drive is stationary in a change of state.

“Behavior in quick stop” is only relevant for non motion control configurations (p.30 ≠

x40).

04/13

CM-CAN ACU

173

Содержание Vectron Active Cube

















































































































































































































































Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды

BONFIGLIOLI Vectron Active Cube, Руководство пользователя

Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды