BONFIGLIOLI Vectron Active Cube Скачать руководство пользователя страница 18

Страница: 18 / 240

2.10.5.1

The five safety rules

When working on/in electrical plants, always follow the five safety rules:

Isolate

Secure to prevent restarting

Check isolation

Earth and short-circuit,

Cover or shield neighboring live parts.

2.10.6

Safe operation

•

During operation of the frequency inverter, always comply with the applicable national and inter-

national regulations/laws on work on electrical equipment/plants.

•

Before commissioning and the start of the operation, make sure to fix all covers and check the

terminals. Check the additional monitoring and protective devices according to the applicable na-

tional and international safety directives.

•

During operation, never open the machine/plant

•

Do not connect/disconnect any components/equipment during operation.

•

The machine/plant holds high voltage levels during operation, is equipped with rotating parts

(fan) and has hot surfaces. Any unauthorized removal of covers, improper use, wrong installation

or operation may result in serious injuries or material damage.

•

Some components, e.g. the heat sink or brake resistor, may be hot even some time after the ma-

chine/plant was shut down. Don't touch any surfaces directly after shutdown. Wear safety gloves

where necessary.

•

The frequency inverter may hold dangerous voltage levels until the capacitor in the DC link is dis-

charged. Wait for at least 3 minutes after shutdown before starting electrical or mechanical work

on the frequency inverter. Even after this waiting time, make sure that the equipment is deener-

gized in accordance with the safety rules before starting the work.

•

In order to avoid accidents or damage, only qualified staff and electricians may carry out the work

such as installation, commissioning or setup.

•

In the case of a defect of terminals and/or cables, immediately disconnect the frequency inverter

from mains supply.

•

Persons not familiar with the operation of frequency inverters must not have access to the fre-

quency inverter. Do not bypass nor decommission any protective facilities.

•

The frequency inverter may be connected to power supply every 60 s. This must be considered

when operating a mains contactor in jog operation mode. For commissioning or after an emer-

gency stop, a non-recurrent, direct restart is permissible.

•

After a failure and restoration of the power supply, the motor may start unexpectedly if the Auto

Start function is activated.

If staff is endangered, a restart of the motor must be prevented by means of external circuitry.

•

Before commissioning and the start of the operation, make sure to fix all covers and check the

terminals. Check the additional monitoring and protective devices according to EN 60204 and ap-

plicable the safety directives (e.g. Working Machines Act or Accident Prevention Directives).

CM-CAN ACU

04/13

Содержание Vectron Active Cube

















































































































































































































































Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды

BONFIGLIOLI Vectron Active Cube, Руководство пользователя

Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды