BONFIGLIOLI Vectron Active Cube Скачать руководство пользователя страница 45

Страница: 45 / 240

Objects

The available objects are marked via Index/Subindex and are to be addressed via this

identification. This chapter describes all available objects.

12.1

Objects tabular overview

The objects are displayed in the next tables. The following definitions apply:

Access type

Read only

The PLC is only allowed to read the data from the ACU.

Read/write

The PLC is granted full access (read and write) to the ACU data.

Data type

Unsigned32

32 Bit value:

0…2

-1

0…0xFFFF FFFF

Unsigned16

16 Bit value:

0…2

-1

0…0x FFFF

(0…65535)

Unsigned8

8 Bit value:

0…2

-1

0…0xFF

(0…255)

Integer32

Signed 32 Bit value: -2

…2

-1

0x8000 0000…0x7FFF FFFF

Integer16

Signed 16 Bit value: 2

…2

-1

0x8000…0x7FFF

(-32768…32767)

Integer8

Signed 8 Bit value: - 2

…2

-1

0x80…0x7F

(-128…127)

Visible String

String up to 99 characters long. Transmission via Segment-

ed Transfer.

PDO mapping

This object cannot be used for PDO exchange, only SDO is appli-

cable.

This object can be transmitted as PDO from ACU.

This object can be transmitted as PDO to ACU.

“Highest Sub-index supported” displays the highest Sub-index that is supported by

this object.

12.1.1

Communication objects

Index

SubIndex

Name

SDO Access

Data type

PDO-mapping

0x1000

Device type

Read only

Unsigned32

0x1001

Error register

Read only

Unsigned8

0x1005

COB-ID SYNC object

Read/write

Unsigned32

0x1006

Communication cycle period

Read/write

Unsigned32

0x1007

Synchronous window length

Read/write

Unsigned32

0x1008

Manufacturer device name

Read only

Visible string

0x1009

Manufacturer hardware

version

Read only

Visible string

0x100A

Manufacturer software

version

Read only

Visible string

0x100C

Guard time

Read/write

Unsigned16

0x100D

Life time factor

Read/write

Unsigned8

0x1010

Store parameters

Highest sub-index supported

Read only

Unsigned8

Save all parameters

Read/write

Unsigned32

Save communication pa-

rameters

Read/write

Unsigned32

Save application parameters

Read/write

Unsigned32

04/13

CM-CAN ACU

Содержание Vectron Active Cube

















































































































































































































































Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды

BONFIGLIOLI Vectron Active Cube, Руководство пользователя

Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды