BONFIGLIOLI Vectron Active Cube Скачать руководство пользователя страница 206

Страница: 206 / 240

Basic functions

The control bit

sequence mode decides between execution of one single motion block

(

sequence mode = 0) and execution of a sequence of motion blocks (sequence mode

= 1).

In both cases the selection of the desired motion block (motion block number of single

motion block or start motion block number of motion block sequence) is done by cal-

culating the motion block number from

motion block select with the rising edge of

start motion block

While the selected motion block or motion block sequence is processed

motion block

in progress is set to 1. Motion block in progress remains 1 until the motion block pro-

cessing is finished. When using a single motion block

motion block in progress is set

to 0 with completion of the single motion block. Otherwise when using a motion block

sequence

motion block in progress is set to 0 when reaching a next motion block set-

ting of 0 (end of motion block) or -1 (error) -2 (stop and error) or -3 (quick stop and

error).

While processing a motion block sequence the actual processed motion block is dis-

played by object

0x5FF0

active motion block

If motion block processing is interrupted by setting

start motion block to 0 the axle

stops with the ramp defined by the actual motion block. The interrupted motion

block/motion block sequence can be restarted again by setting

resume and a rising

edge of

start motion block.

resume is set to 1 and there is no valid motion block available the motion block

defined by

motion block select will be used. A valid motion block is displayed by object

0x5FF1

motion block to resume

Motion block to resume displays -1 in case there is no

valid motion block or the last motion block/motion block sequence was not interrupt-

ed.

Target reached is set by motion blocks with absolute or relative positioning when the

actual position reaches the

position window.

In gear is set when the function electronic gear is used and the gear is coupled.

Setting

Halt to 1 interrupts an actual processed motion block. The axle is stopped with

the ramp defined by the actual motion block. When reaching velocity 0

target reached

is set to 1. The drive remains in state

operation enabled. Resetting Halt to 0 restarts

processing of the interrupted motion block.

206

CM-CAN ACU

04/13

Содержание Vectron Active Cube

















































































































































































































































Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды

BONFIGLIOLI Vectron Active Cube, Руководство пользователя

Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды