BONFIGLIOLI Vectron Active Cube Скачать руководство пользователя страница 71

Страница: 71 / 240

Object 0x1800/0x1801/0x1802 transmission type

value

meaning

description

Synchronous

Update TxPDO data and send on SYNC only when

data has changed

1 … 240

Synchronous

Update TxPDO data and send on each “n” SYNC

241 … 251

Reserved

Value not allowed

252

synchronous/RTR Update TxPDO data on SYNC and send on following

RTR

253

asynchronous/RTR Update TxPDO data and send on RTR

254

asynchronous

Event driven (manufacturer specific)

255

asynchronous

Event driven (profile specific) default value

Values 254 + 255 are handled identically. Send TxPDO on data change or event time.

Inhibit time: The inhibit time is the minimum time distance between two consecu-

tive TxPDOs for asynchronous TxPDOs. During the inhibit time, the TxPDO is not send

again. Therefore a value change occurring in this time is send earliest after the inhibit

time has elapsed. The value range is 0…65535.

The inhibit time is set in hundreds of microseconds, e. g. a value of 300 is

300 *100 us = 30 ms.

The device internal time resolution for the inhibit time is in milliseconds, the last digit

is always converted to “0”. An inhibit time value = 37 is truncated to 30 [3.7 ms



ms].

Values less than 10 are interpreted as 0.

Event time: The event time is the time distance between two consecutive TxPDOs

whenever the TxPDO data has not changed (cycle time). If the inhibit time is set to

zero the TxPDO is only sent on a change of the TxPDO’s data. The value range is

0…65535.

The event time is set in milliseconds, e.g. a value of 2000 = 2000 ms.

04/13

CM-CAN ACU

Содержание Vectron Active Cube

















































































































































































































































Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды

BONFIGLIOLI Vectron Active Cube, Руководство пользователя

Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды