BONFIGLIOLI Vectron Active Cube Скачать руководство пользователя страница 161

Страница: 161 / 240

13.5

Move away from Hardware limit switches

If a hardware limit switch was activated, depending on parameter setting 1143

Fault

reaction

a fault message is triggered and the direction of rotation is disabled.

After a fault reset the still enabled direction of rotation can be used for a motion. For

the moving away all operating modes can be used in general as long as the drive

command executes the movement in the enabled direction.

As long as the limit switch is still triggered, the limit switch warning in the status word

and in the actual parameters 269

Warnings

, 273

Warnings Application

und 275

Controller status

remains set. As soon as the limit switch is free, the warning in the

status word and the actual parameters is reset.

For an easy Moving away from a Limit switch the mode “-2 Move away from limit

switch” can be used (chapter 14.4.814.4.7).

04/13

CM-CAN ACU

161

Содержание Vectron Active Cube

















































































































































































































































Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды

BONFIGLIOLI Vectron Active Cube, Руководство пользователя

Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды