BONFIGLIOLI Vectron Active Cube Скачать руководство пользователя страница 164

Страница: 164 / 240

Inverter Control

The control of the frequency inverter can, in principle, be carried out using three op-

eration modes. These are set via the data set change-over capable parameter

Lo-

cal/Remote

412.

Parameter

Setting

No.

Description

Min.

Max.

Fact. sett.

412 Local/Remote

For operation with CANopen

, only the settings 0, 1 and 2 are relevant. The remain-

ing settings relate to the possibilities of control via the KP500 control unit.

Control mode

Function

0 -

Control via digital in-

puts

(chapter 14.1)

The Start and Stop command as well as the statement

of the direction of rotation are via digital input signals.

1 -

Control via

state machine

(chapters 14.2, 14.3,

14.4)

The inverter is controlled by the

Control word.

Only in this control mode are the motion control

functions supported by

Control w ord and modes

of operation as defined with CANopen

DS402.

2 -

Control via

remote digital inputs

(chapter 14.1)

The Start and Stop command as well as the statement

of the direction of rotation are via digital input signals

emulated by the bits of the

Control word.

Parameter

Local/Remote

412 is data set change-over capable. Thus, it is possible to

switch over between the various control modes via the data set selection.

The data set change-over can be carried out locally on the frequency inverter via

digital inputs or via the bus. For data set change-over via the bus, parameter

Data

set selection

414 is used.

Parameter

Setting

No.

Description

Min.

Max.

Fact. sett.

414 Data set selection

With

Data set selection

414 = 0, the data set change-over via digital inputs is active.

Data set selection

414 has been set to 1, 2, 3, or 4, the corresponding data set is

activated. Data set change-over via the digital inputs is then disabled.

Via parameter

Active data set

249, the currently selected data set can be read out.

Active data set

249 states the activated data set with the value 1, 2, 3 or 4. This is

independent of whether the data set change-over was carried out via digital inputs or

via

Data set selection

414.

164

CM-CAN ACU

04/13

Содержание Vectron Active Cube

















































































































































































































































Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды

BONFIGLIOLI Vectron Active Cube, Руководство пользователя

Результаты поиска

Содержание Vectron Active Cube

Отзывы:

Похожие инструкции для Vectron Active Cube

Бренды по названию

Популярные бренды