BERGER 356280, Руководство пользователя

Страница: 20 / 59

GB GB
38 39
Two-axle mode: Single-axle mode:
Two-axis mode (only one driven axis)
Make sure that the batteries are inserted in the remote control as described in the previous
section (Operation - Remote Control Functions)� Turn on the battery disconnect switch to supply
power to the electronic control unit (2); a red LED lights up� Press the power button twice
(Fig�1�A) to switch on the remote control�
On your remote control (1), press and hold the [ENG] (fi g�1�I) and [DENG] (fi g�1�J) buttons for
one second to enter pairing mode� The indicator LED (Fig�1�B) on your remote control should
fl ash green continuously� Press the small sync button (fi g�3) on your electronic control unit (2)�
The LED on this box should fl ash red rapidly before making a small clicking sound� The indica-
tor LED (Fig�1�B) on your remote control should be solid green and the LED on the electronic
control unit (2) should fl ash red slowly to indicate that the two are paired�
The remote control is in single-axis mode by default� To select dual-axis mode, press and hold
[RL] (Fig�1�G) and [FN] (Fig�1�K) for 5 seconds� The remote beeps once to indicate that the mode
has been set to dual axis� Once set, the remote control and the control unit remember the
assignment and are fully functional after switching on�
Two-axle mode: Single-axle mode:
AWD mode (dual axle, both driven)
To confi gure your system for AWD mode, the remote control (1) only needs to be paired with
the electronic control unit of the front axle (2)� To do this, fi rst make sure that the data cable (4)
is correctly connected to both control units as described in the section „Installation - Electrical/
Electronic Components (AWD Confi guration)“� Make sure that the batteries are also inserted in
the remote control as described in the previous section (Operation - Pairing the remote control /
Mode selection)�
Turn on the battery disconnect switch to power both control units; a red LED lights up on each
box� Press the power button twice (Fig�1�A) to switch on the remote control�
On your remote control (1), press and hold the [ENG] (Fig�1�I) and [DENG] (Fig�1�J) buttons for
one second to enter pairing mode� The indicator LED (Fig�1�B) on your remote control should
fl ash green continuously� Press the small sync button (fi g�3) on the electronic control unit of
the front axle (2)� The LED on this box should fl ash red rapidly before a small clicking sound is
heard� The indicator LED (fi g�1�B) on your remote control should be solid green and the LED on
the electronic control unit (2) should fl ash red slowly to indicate that it is paired�
The remote control is in single-axle mode by default� To select AWD mode, press and hold the
[RL] (Fig�1�G) and [FN] (Fig�1�K) buttons for 5 seconds to fi rst select dual-axle mode� The remote
beeps once to indicate that the mode has been set to dual axis� Press and hold the [RL] (fi g�1�G)
and [FN] (fi g�1�K) buttons again for 5 seconds to select AWD mode� The remote control beeps
OPERATION - PAIRING THE REMOTE CONTROL / MODE SELECTION
The procedure for pairing the remote control depends on the confi guration of the manoeuvring
aid you have installed in your caravan� It is extremely important that the remote control is set
in the correct mode to ensure that the manoeuvring aid functions as intended� With two-axle
vehicles, for example, the turning possibilities are quite different from those of a single-axle ca-
ravan� Only if you set the manoeuvring aid correctly can you get the best possible performance
out of it�
Familiarise yourself with the functions of the remote control (see ‚Operation - Remote con-
trol functions‘) and the structure of the electronic control unit� These must be set to both the
correct model and mode for your axle confi guration� To set the correct model, follow the table
below:
Model Selection Description Buttons
Manoeuvring aid
titanium
Press and hold [FN] (Fig�1�K) and [F]
(Fig�1�C) for 5 seconds� 5 sec
To set the correct mode, see the following sections:
Single-axis mode
Make sure the batteries are inserted in the remote control as described in the previous section
(Operation - Remote Control Functions)� Turn on the battery disconnect switch to supply power
to the electronic control unit (2); a red LED lights up� Press the power button twice (Fig�1�A) to
switch on the remote control�
On the remote control (1), press and hold the [ENG] (fi g�1�I) and [DENG] (fi g�1�J) buttons for one
second to enter pairing mode� The indicator LED (Fig�1�B) on your remote control should fl ash
green continuously� Press the small sync button (fi g�3) on your electronic control unit (2)� The
LED on this box should fl ash red rapidly before making a small clicking sound� The indicator LED
(Fig�1�B) on your remote control should be solid green and the LED on the electronic control
unit (2) should fl ash red slowly to indicate that the two are paired�
If you do not change this, the remote control will be in single axis mode by default� If the re-
mote control is not in default mode, press and hold the [FL] (fi g� 1�E) and [FN] (fi g� 1�K) buttons
for 5 seconds to select single axis mode� The remote beeps once to indicate that the mode has
been set to Single Axis� Once set, the remote control and control unit remember their assign-
ment and are fully functional after switching on�