BERGER 356280, Руководство пользователя

Страница: 21 / 59

GB GB
40 41
button (Fig�1�A)� The indicator LED (Fig�1�B) of the remote control lights up� Switch on both
drive units as described in the section „Operation - Switching on/off“ in this manual� Before
operating the manoeuvring aid, release the handbrake�
Move the vehicle using the various buttons, always paying attention to your surroundings and
the terrain� In single-axle mode, the [FR] (Fig�1�D) and [RL] (Fig�1�G) or [FL] (Fig�1�E) and [RR]
(Fig�1�F) buttons must be pressed together to use the „turn on the spot“ function� This function
is disabled in two-axle and AWD mode�
Turn on the spot options:
The soft start function of the motors means that the manoeuvring aid operates at a lower
speed for the fi rst 2�5 seconds� Note that the general speed may increase slightly when driving
downhill and decrease slightly when driving uphill� The manoeuvring aid is more effi cient when
the caravan is reversing up a slope�
After manoeuvring, apply the handbrake before disconnecting the drive rollers from the tyres�
Switch off the system by double-clicking the power button (Fig� 1�A) on the remote control� The
indicator LED (Fig�1�B) on the remote control goes out� Turn off the battery disconnect switch to
cut off the power supply to the electronic control unit(s)�
Keep the remote control and the battery disconnect switch in a safe place (out of reach of child-
ren or other unauthorised persons)�
After manoeuvring, be sure to apply the vehicle‘s handbrake before disengaging the manoeuv-
ring aid or switching off the electronic unit or handset� Never rely on the manoeuvring aid to
act as a brake�
Coupling and uncoupling
It is possible to position the caravan‘s trailer coupling exactly over the trailer coupling of a stati-
onary vehicle using the manoeuvring aid, but this should be done with care�
Use the movement buttons on the remote control to move the caravan up to the car� It is better
to reach the trailer hitch with several short „trips“ than to try to do it with one „trip“� When
the trailer hitch is just above the ball head of the car, lower the trailer hitch onto the ball head
and engage with the jockey wheel as usual� Uncouple the manoeuvring aid from the caravan‘s
tyres (see Operation - Coupling/uncoupling the manoeuvring aid)�
Do not attempt to pull your vehicle with the manoeuvring aid switched on! Make sure that all
rollers are fully disengaged� If you try to drive away with the manoeuvring aid engaged, the
manoeuvring aid, the tyres of your caravan and your towing vehicle will be damaged!
in a short sequence to indicate that AWD mode has been set� The LEDs on both electronic con-
trol units (2) should now fl ash slowly to indicate that they are synchronised with each other and
with the remote control (1)�
To test the confi guration, make sure that all drive rollers are disengaged and there are no
obstructions and press and hold the [F] button (Fig�1C)� All four rollers should rotate� If no drive
rollers turn or only one axle turns, repeat the AWD setup process starting with a full reset of
your remote (1) as described in the note below�
Note: For the remote control (1) to be paired correctly for AWD, it must not have previously
connected to any of the electronic control units (4)� If this is the case, follow the instructions in
the „Complete remote control reset“ section of this manual� Turn off the battery disconnect
switch to cut the power to the electronic control units (2)� Repeat the AWD pairing procedure
as described above�
Two-axle mode: Single-axle mode:
Completely resetting the remote control
There may be times when you need to clear the pairing memory or reset the default settings
of your remote control� In this case, perform a full reset of your remote control (1) by pressing
and holding the power button (Fig�1�A) and [FN] (Fig�1�K) until the remote control switches off
(approx� 10 seconds)� The next time you switch on the remote control, the LED will light up
solid red� Pair your remote control as required by following the relevant section of this manual
and ensuring that you select the correct axis mode�
Completely resetting the remote control
OPERATION - ENGAGING AND DISENGAGING THE MANOEUVRING AID
Always make sure that the handbrake of the caravan is applied before you engage or disenga-
ge the manoeuvring aid to prevent unintentional movements of the caravan� Only release the
handbrake when the manoeuvring aid is securely connected to the tyres and you are ready to
move the caravan�
OPERATION - MANOEUVRING
Attention! Please read the safety instructions for operation carefully BEFORE you start using
your Berger Ragierhilfe Titanium�
Familiarise yourself with the arrangement of the remote control buttons by referring to Fig� 1
and the section „Operation - Functions of the remote control“ in this manual�
Switch on the battery isolator switch� Activate the remote control by double-clicking the power
x2