Beckman Coulter Allegra X-30 Series Скачать руководство пользователя

Страница: 5 / 64

PN B05529AE

Safety Notice

Read all product manuals and consult with Beckman Coulter-trained personnel before attempting

to operate the instrument. Do not attempt to perform any procedure before carefully reading all

instructions. Always follow product labeling and manufacturer’s recommendations. If in doubt as

to how to proceed in any situation,

contact us

Alerts for Danger, Warning, Caution, Important, and Note

DANGER

DANGER indicates an imminently hazardous situation which, if not avoided,

will result in death or serious injury.

WARNING

WARNING indicates a potentially hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous situation, which, if not avoided,

may result in minor or moderate injury. It may also be used to alert against unsafe

practices.

IMPORTANT

IMPORTANT is used for comments that add value to the step or procedure being performed.

Following the advice in the Important adds benefit to the performance of a piece of equipment or to a

process.

NOTE

NOTE is used to call attention to notable information that should be followed during installation, use,

or servicing of this equipment.

Safety During Installation and/or Maintenance

These centrifuges each weigh 48 kg/106 lb (non-refrigerated model) or 78 kg/172 lb (refrigerated

model). DO NOT attempt to lift or move one of them without assistance from another person.

Any servicing of this equipment that requires removal of any covers can expose parts which involve

the risk of electric shock or personal injury. Make sure that the power switch is turned off and the

instrument is disconnected from the main power source by removing the Mains (power) plug from

the outlet receptacle, and refer such servicing to qualified personnel.

Do not replace any centrifuge components with parts not specified for use on this instrument.

Содержание Allegra X-30 Series

































































Результаты поиска

Содержание Allegra X-30 Series

Отзывы:

Похожие инструкции для Allegra X-30 Series

Бренды по названию

Популярные бренды

Beckman Coulter Allegra X-30 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Allegra X-30 Series

Отзывы:

Похожие инструкции для Allegra X-30 Series

Бренды по названию

Популярные бренды