Beckman Coulter Allegra X-30 Series Скачать руководство пользователя

Страница: 60 / 64

PN B05529AE

A-4

Installation

Test Run

WARNING

To reduce the risk of electrical shock, this equipment uses a three-wire electrical

cord and plug to connect the centrifuge to earth-ground. To preserve this safety

feature:
• Make sure that the matching wall outlet receptacle is properly wired and

earth-grounded. Check that the line voltage agrees with the voltage listed on

the name rating plate affixed to the centrifuge.

• Never use a three-to-two wire plug adapter.
• Never use a two-wire extension cord or a two-wire non-grounding type of

multiple-outlet receptacle strip.

Test Run

NOTE

The centrifuge must be plugged in and the power switch turned to on position (

) before the door

can be opened.

We recommend that you make a test run to ensure that the centrifuge is in proper operating

condition following shipment. See

CHAPTER 2,

Operation

for instructions on operating the

centrifuge.

After completing the test run, log on to www.beckmancoulter.com to register your centrifuge. This

validates the centrifuge warranty and ensures your receipt of further information regarding new

accessories and/or modifications as they become available.

Содержание Allegra X-30 Series

































































Результаты поиска

Содержание Allegra X-30 Series

Отзывы:

Похожие инструкции для Allegra X-30 Series

Бренды по названию

Популярные бренды

Beckman Coulter Allegra X-30 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Allegra X-30 Series

Отзывы:

Похожие инструкции для Allegra X-30 Series

Бренды по названию

Популярные бренды