Beckman Coulter Allegra X-30 Series Скачать руководство пользователя

Страница: 53 / 64

PN B05529AE

4-3

Care and Maintenance

Tube Breakage

Tube Breakage

If a glass tube breaks, and all the glass is not contained in the bucket or rotor, you must thoroughly

clean the interior of the chamber bowl.

WARNING

Be careful when examining or cleaning the sealing gasket or chamber, as sharp

glass fragments may be embedded in their surfaces.

Examine the gasket to make sure that no glass particles are retained in it.

Carefully remove any glass particles that may remain.

Carefully wipe away any glass particles that remain in the bowl.

Decontamination

If the centrifuge and/or accessories are contaminated with radioactive or pathogenic solutions,

perform appropriate decontamination procedures. Refer to

Chemical Resistances

(IN-175) to be sure

the decontamination method will not damage any part of the centrifuge.

Sterilization and Disinfection

The centrifuge is finished with urethane paint. Ethanol (70%)

may be used on this surface. See

Chemical Resistances

for more information regarding chemical resistance of centrifuge and

accessory materials.

While Beckman Coulter has tested these methods and found that they do not damage the

centrifuge, no guarantee of sterility or disinfection is expressed or implied. When sterilization or

disinfection is a concern, consult your laboratory safety officer regarding proper methods to use.

* Flammability hazard. Do not use in or near operating centrifuges.

Содержание Allegra X-30 Series

































































Результаты поиска

Содержание Allegra X-30 Series

Отзывы:

Похожие инструкции для Allegra X-30 Series

Бренды по названию

Популярные бренды

Beckman Coulter Allegra X-30 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Allegra X-30 Series

Отзывы:

Похожие инструкции для Allegra X-30 Series

Бренды по названию

Популярные бренды