Beckman Coulter Allegra X-30 Series Скачать руководство пользователя

Страница: 25 / 64

PN B05529AE

1-7

Description

Controls and Indicators

Digital Displays

Digital displays indicate rotor speed, run time, rotor chamber temperature, and numbers that

represent selected acceleration and deceleration profiles (see

Figure 1.6

). When the power is turned

on, they show the operating parameters of the most recent run performed before the power was

turned off. The displays serve a dual purpose.

•

When the run parameters are being set (the input mode), the displays show the set values

(those selected by the operator). When a run- parameter key (for example,

TIME

RPM

) is

pressed, the appropriate display flashes to indicate that data can be entered.

•

The

actual

(real-time) operating conditions of the centrifuge are displayed during the run, after

START

is pressed.

NOTE

Error messages (see Section 4) also appear on the displays, when applicable. The centrifuge emits a

series of audible tones to alert the user to an error condition.

Figure 1.6

Digital Displays

RPM/RCF/ROTOR

•

In input mode

the RPM/RCF/ROTOR display shows the value of the parameter

being set, depending on the programming key pressed (

RPM

RCF

, or

ROTOR

For example, if the

ROTOR

programming key is pressed, a rotor number

appears on the

SPEED

display.

•

During centrifugation

, the

SPEED

display shows the speed of the rotor in rpm.

If the

RCF

key is pressed while the centrifuge is running, the RCF value is

displayed.

TIME

•

During a

timed run

(between 1 minute and 9 hours, 59 minutes), the

TIME

display begins counting down when the rotor starts to spin and continues the

countdown until deceleration begins. The

TIME

display indicates the remaining

run time in hours and minutes.

•

During a

continuous run

(less than 1 minute or more than 9 hours, 59 minutes

selected), countdown time is not displayed. Instead, the infinity (



) symbol,

indicating continuous operation, lights up and the

TIME

display shows time

elapsed since the run start. After 9 hours and 59 minutes the timer resets to 0

and continues counting elapsed time.

TEMP °C

(refrigerated

models only)

During standby (that is, the centrifuge is turned on but not spinning) and operation,

the

TEMP °C

display shows the actual temperature inside the rotor chamber (



2°C

at an ambient temperature of 20°C).

ACCEL/DECEL

The

ACCEL/DECEL

display shows the acceleration curve that was selected for the

run. The deceleration curve number can be displayed by pressing the

DECEL

key.

Содержание Allegra X-30 Series

































































Результаты поиска

Содержание Allegra X-30 Series

Отзывы:

Похожие инструкции для Allegra X-30 Series

Бренды по названию

Популярные бренды

Beckman Coulter Allegra X-30 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Allegra X-30 Series

Отзывы:

Похожие инструкции для Allegra X-30 Series

Бренды по названию

Популярные бренды