Beckman Coulter Allegra X-30 Series Скачать руководство пользователя

Страница: 61 / 64

PN B05529AE

Warranty-1

Beckman Coulter, Inc.

Allegra X-30 Series Centrifuge Warranty

Subject to the exceptions and upon the conditions specified below, Beckman Coulter agrees to correct, either

by repair, or, at its election, by replacement, any defects of material or workmanship which develop within

one (1) year after delivery of the Allegra X-30 series centrifuge (the product), to the original Buyer by

Beckman Coulter or by an authorized representative provided that investigation and factory inspection by

Beckman Coulter discloses that such defect developed under normal and proper use.

Some components and accessories by their nature are not intended to and will not function for as long as one

(1) year. A complete list of such components or accessories is maintained at the factory and at each

Beckman Coulter District Sales Office. The lists applicable to the products sold hereunder shall be deemed to

be part of this warranty. If any such component or accessory fails to give reasonable service for a reasonable

period of time, Beckman Coulter will repair or, at its election, replace such component or accessory. What

constitutes either reasonable service and a reasonable period of time shall be determined solely by

Beckman Coulter.

Replacement

Any product claimed to be defective must, if requested by Beckman Coulter, be returned to the factory,

transportation charges prepaid, and will be returned to Buyer with the transportation charges collect unless

the product is found to be defective, in which case Beckman Coulter will pay all transportation charges.

Conditions

Beckman Coulter shall be released from all obligations under all warranties either expressed or implied, if the

product(s) covered hereby are repaired or modified by persons other than its own authorized service

personnel, unless such repair in the sole opinion of Beckman Coulter is minor, or unless such modification is

merely the installation of a new Beckman Coulter plug-in component for such product(s).

Disclaimer

IT IS EXPRESSLY AGREED THAT THE ABOVE WARRANTY SHALL BE IN LIEU OF ALL WARRANTIES OF FITNESS

AND OF THE WARRANTY OF MERCHANTABILITY AND THAT NEITHER BECKMAN COULTER, INC. NOR ITS

SUPPLIERS SHALL HAVE ANY LIABILITY FOR SPECIAL OR CONSEQUENTIAL DAMAGES OF ANY KIND

WHATSOEVER ARISING OUT OF THE MANUFACTURE, USE, SALE, HANDLING, REPAIR, MAINTENANCE, OR

REPLACEMENT OF THE PRODUCT.

Содержание Allegra X-30 Series

































































Результаты поиска

Содержание Allegra X-30 Series

Отзывы:

Похожие инструкции для Allegra X-30 Series

Бренды по названию

Популярные бренды

Beckman Coulter Allegra X-30 Series, Инструкция по эксплуатации

Результаты поиска

Содержание Allegra X-30 Series

Отзывы:

Похожие инструкции для Allegra X-30 Series

Бренды по названию

Популярные бренды