manualshive.com logo in svg

B. Braun Dialog+, Руководство по обслуживанию

B. Braun Dialog+ - устройство для проведения инфузионной терапии, изготовленное высокой немецкой компанией B. Braun. Для получения инструкций по обслуживанию и использованию бесплатно загрузите Руководство по эксплуатации с {веб-сайта}. Устройство обеспечивает надежное и точное введение лекарственных препаратов для потребностей пациента.

Поделиться
Скачать
background image

 

5.  Technical  Safety  Inspection  and  Preventive  Maintenance 

1 / 2 0 1 0  

5  -  1

 

 

BA-TE-DE08C M.KAY 

SW9xx_SM_Chapter 5-1_1-2010.doc/pdf <110301> yymmdd 

B. Braun Avitum AG

 

Dialog

+

  

SW 9.xx

 

Copyright 

This document is the property of B. Braun Avitum AG with all rights reserved. 

Service 

Only trained personnel must service the , i.e. repair, maintenance, software installation, 
firmware update, retrofitting and commissioning of the . 
Servicing must only be performed with proper tools, calibration equipment and be in accordance 
with the most recent revision of this service manual/technical information, which must be 
clearly and thoroughly understood. 

Prevent Electrical Shock Hazard 

Switch off the and disconnect unit from mains if you have to open the machine for 
servicing. Do not touch any exposed wiring or conductive surfaces while the  is opened. 
The voltages present when electrical power is connected to the  can cause serious injury 
or death. 

ESD Information 

Pay attention to ESD information, because electronic components are sensitive to electrostatic 
discharges. 

High Voltage 
in TFT Monitor 

 

If a battery option is present in the machine: 
High voltage can be present at the backlight inverter board BIB in the TFT monitor, even if the 
machine has been disconnected from mains. Pull out the battery compartment in the base 
platform and switch off the battery voltage (remove fuse) before opening the machine. 

Protective Conductor in TFT Housing 

If the TFT housing had to be opened during a service job, the tight seat of the protective 
conductors in the TFT housing must be checked. 

TSM Service Program 

Only activate the TSM service program for service activities. It is prohibited to connect a patient 
to the and to run a therapy if the TSM service program is activated in the . If 
the TSM service program is activated the complete alarm system is disabled. The TSM service 
program is started in the service mode: digital board, service switch S1, position 2. 

Software 

The software is installed in the software mode: digital board, service switch S1, position 3. 

Therapy Mode 

After completion of all procedures switch back to the therapy mode: digital board, service 
switch S1, position 0. 

Calibration 

Only perform a calibration after the  has reached working temperature, and the machine 
was disinfected and decalcified. You should save the calibration data to the hard disk drive 
before you exit the TSM service program: 

TSM Main Menu

, 

File Operations

, 

Save Calibration 

Data

. 

Connection and Operation Service Board 

The service board must only be operated in the TSM service program. If the service board is 
connected to the  it is prohibited to connect a patient to the and to run a 
therapy. 

Prevent Chemical Burns and Scalding 

During servicing on running machines: prevent chemical burns and scalding of the skin due to 
the penetration of disinfectant or hot liquid. 

Contaminated Machines 

Protective gear should be worn in case of servicing of assumed contaminated machines. 

Cover in Rear Door 

Servicing of mechanical assembly groups (components in contact with fluid): the cover in the 
rear door must be assembled during servicing because it serves as a spray protection for the 
assembled SMPS-MC. 

Tubing 

Tubing must be replaced only by the same tubing type/length and identical installation manner. 

Make sure that the tubings in the machine are not kinked or twisted after servicing (e.g. if sub-
racks are pulled out and inserted again). The tubing must not touch moving/rotating 
components (e.g. motors of gear pumps). 

Wiring 

Wiring must be replaced only by the same cable type/length and identical installation manner. 
The cables must not touch moving/rotating components (e.g. motors of gear pumps). 

Fuses 

If fuses are replaced they must exactly match the type and rating specified by the manufacturer 
in the spare parts list/technical information. Where applicable: fuses must be approved by 
UL/CSA. 

Spare Parts 

Only use original spare parts manufactured and sold by B. Braun Avitum AG. 

Ambient Temperature 

Before the  is switched on the machine must have room temperature (see operating 
manual, chapter 15). 

!

 

 

 

Содержание Dialog+








































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Dialog+

Haki 564 User Manual preview
564
Бренд: Haki Страницы: 24
Dakota Digital VHX-66F-BRO Installation preview
VHX-66F-BRO
Бренд: Dakota Digital Страницы: 5
R-Biopharm RIDA qLine ZG2601 Operation Instructions Manual preview
RIDA qLine ZG2601
Бренд: R-Biopharm Страницы: 23
U-Line H-5334 Quick Start Manual preview
H-5334
Бренд: U-Line Страницы: 9
U-Line Green Machine H-3518 Instructions preview
Green Machine H-3518
Бренд: U-Line Страницы: 3
Varytec LED Street Bar 16x3W RGB IP65 User Manual preview
LED Street Bar 16x3W RGB IP65
Бренд: Varytec Страницы: 9
VARILITE VL1600 PROFILE Quick Start Manual preview
VL1600 PROFILE
Бренд: VARILITE Страницы: 8
Vari Lite EVENTPROFILE VL800 User Manual preview
EVENTPROFILE VL800
Бренд: Vari Lite Страницы: 34
Varex Imaging Optica 30 Series User Manual preview
Optica 30 Series
Бренд: Varex Imaging Страницы: 36
Wassermann WAPO-Ex User Manual preview
WAPO-Ex
Бренд: Wassermann Страницы: 24
Gaspardo PI Use And Maintenance preview
PI
Бренд: Gaspardo Страницы: 44
Yamaha PLG150-AN Tutorial preview
PLG150-AN
Бренд: Yamaha Страницы: 5
ZacUrate 500E User Manual preview
500E
Бренд: ZacUrate Страницы: 2
ZacUrate 430P User Manual preview
430P
Бренд: ZacUrate Страницы: 2
ICS 8099 Instruction Manual preview
8099
Бренд: ICS Страницы: 156
Osram ARCHISHAPE 2.0 Linear Instruction preview
ARCHISHAPE 2.0 Linear
Бренд: Osram Страницы: 7
ebm-papst R1G225-AG15-11 Operating Instructions Manual preview
R1G225-AG15-11
Бренд: ebm-papst Страницы: 10
Eaton CEAG Exit Cube 33822 LED CGLine+ Mounting And Operating Instructions preview
CEAG Exit Cube 33822 LED CGLine+
Бренд: Eaton Страницы: 20

Бренды по названию

Популярные бренды

Загрузить еще бренды