- 59 -
XGSM
Credit request personalization:
In this menu, it is possible to personalize the credit request method, in the case
of variation by the operator. The control panel is programmed for the request by the following operators:
Vodafone > call number = 404
TIM > SMS = PRE CRE SIN \ SMS calling number = 40916
WIND > SMS = SALDO \ SMS calling number = 4155
DO NOT USE THE FOLLOWING ACTION IF THE REQUEST PROCEDURE MATCHES THE ONE ALREADY PROGRAMMED.
Credit telephone number:
Introduce the operator phone number to be used by the control panel for calling/
forwarding the SMS
Use SMS Credit:
Activating this function, the control panel send the indicated SMS in “Credit SMS” for the credit
request. Placing NO, the control panel will ring only once at the phone number indicated in “Credit phone number”.
Credit SMS:
In this menu, it is possible to personalize the credit SMS message, as required by the GMS operator.
Press
(CLR)
to vary
Enter the telephone number
Press
(
)
and
(
)
to move
Press
(ENT)
to confirm
Dialler
XGSM485
The XGSM485 can contain two SIM Cards. If both SIM Cards are installed, at the first power feed, by default the
operation starts with the Main SIM Card
(SIM Card A)
and there is an automatic changeover to the Secondary
SIM Card (
SIM Card B
). This is controlled by the following events:
• No credit
• GSM network down
• No GSM field
• GSM module operating faults
After switching to the Secondary SIM Card, the device sets a 240-minute timer for automatically switching
back to the Main SIM Card. The device may switch back the Main SIM Card earlier, however, if any of the
above occurs to the second one in the meantime.
Communicate Tamper:
When this function is enabled and communication with the central control unit in
RS485 is down, the XGSM485 autonomously communicates the Tamper event and any GSM faults to the
first 8 telephone numbers programmed for communicating these events in GSM.
Communicate Tamper reset:
When this function is enabled, the XGSM485 communicates resetting of
communication with the central control unit in RS485 and any GSM anomalies to the first 8 telephone
numbers programmed for communicating these events in GSM.
PSTN to XGSM485:
When this function is enabled, the state of the PSTN telephone line connected to the
XGSM485 is controlled.
SIM B available:
When this function is enabled, the presence of a second SIM in the secondary SLOT is
confirmed.
Continuous dialtone:
When this function is enabled and the PSTN telephone line is absent, the
XGSM485Plus generates a continuous rather than an alternating line tone.
Number Rings Answer:
When the Rings Answer function is enabled and the number of rings is greater
than 0, it is possible to call the central control unit with the SIM active in the XGSM485 to obtain an RTC
connection (see “Functions RTC User”).
SiM A (Main SIM)
PIN:
Enter the valid PIN code of the SIM card.
If the PIN code has been disabled this parameter is ignored.
SIM Credit ctrl:
If this function is enabled, the control panel will check the credit of the SIM Card. Should
a rechargeable card be installed, leave “NO”.
GPRS:
The parameters for data connection via XGSM are programmed in this menu
APN (Access Point Name):
Name of the access point (server) to which a mobile device will try to connect
to gain access to the Internet to make data transfers.
APN:
Access point name. If left blank, the panel will use the default names made available by the network
operator used (valid only for Italy): TIM: ibox.tim.it, VODAFONE: web.omnitel.it, WIND: internet.wind
Username:
user name for accessing the APN (if required by the operator)
Password:
password for accessing the APN (if required by the operator)
Credit req. pers.
ENT
Credit tel. num.
Use SMS Credit
NO
Credit SMS
XGSM485
ENT
Tamper commun.
YES
Tamper rst. comm.
NO
PSTN on XGSM485
NO
SIM B available
NO
Cont. dialtone
NO
Num. rings answer
0 (0 . . 16)
PIN
0000
SIM credit ctrl.
YES
GPRS
ENT
APN
ENT
APN
Username
Password
SIM A
ENT
to following
page
from previus
page
Press
(CLR)
to vary
Writing keys:
(1)
abc1
(2)
def2
(3)
ghi3
(4)
jkl4
(5)
mno5
(6)
pqr6
(7)
stu7
(8)
vwx8
(9)
yz.
(0)
_’0
Press
(ENT)
to confirm
Press arrows
(
)
and
(
)
to position the cursor
Press
(ESC)
to go back
Press
(
)
and
(
)
to move
