Avaya IP403 Office Скачать руководство пользователя страница 85

Страница: 85 / 115

Installation Manual

Page 79

IP Office 2.1

40DHB0002USCL Issue 10c (11th May 2004)

Technical Data

Port Pinouts

This section provides the technical specifications for the IP Office ports with the exception of the USB
port and cable. All diagrams are viewed from the front. The USB port and cable (up to 5 meters) are
standard. Refer to

Cables

for cable details.

•

Note:

Throughout the following, Tx = from IP Office and Rx = to IP Office.

Analog Trunk Ports (RJ45)

Pin No.

Description

1-3

Do not use.

4 Ring.

5 Tip.

6-8

Do not use.

Power Fail and POT Ports (RJ45)

Pin No.

Description

1 & 3

Do not use.

Connected to Pin 6*.

Ring.

Tip.

Connected to Pin 2*.

7-8

Do not use.

* Pins 2 and 6 are shorted together and, via a 'ringer' capacitor, connected to in 5.

DS/DT Ports (RJ45)

Pin No.

Description

1-3

Do not use.

4 Sig

Sig 2.

6-8

Do not use.

Содержание IP403 Office




















































































































Результаты поиска

Содержание IP403 Office

Отзывы:

Avaya IP403 Office, Руководство по установке, Страница: 85 / 115

Результаты поиска

Содержание IP403 Office

Отзывы: