Avaya IP403 Office Скачать руководство пользователя страница 72 | Manualshive

Страница: 72 / 115

Avaya IP403 Office Скачать руководство пользователя страница 72

IP Office Installation

Installation Manual

Page 66

IP Office 2.1

40DHB0002USCL Issue 10c (11th May 2004)

Connecting & Checking Two-Wire Telephones

All two-wire devices (POTS) should be tested according to the manufacturer's instructions before
connection to the IP Office system. Connect the two-wire device and make a test call.

Power Fail Telephones and Sockets

All power fail sockets (on IP400 Analog Trunk 16 modules only – see

IP400 Analog Trunk 16

) must be

tested.

To test a power fail socket :

1. Locate the socket and check that it is clearly labeled as a power fail socket.

2. Connect a telephone to the socket.

3. With power to the IP Office system switched on, make a test call.

4. Switch the power to the IP Office system off and again make a test call.

5. Switch the power to the IP Office system back on again.

6. Repeat the test for any other power fail sockets.

•

Note

Where E911 statuary requirements for discrete location identification of a power fail
phone are required on the transmitted CLI, ensure that the relevant installation
programming is completed.

«
...
70
71
72
73
74
...
»

Содержание IP403 Office




















































































































Отзывы:

Нет отзывов